Jump to content
SAU Community

Recommended Posts

hey hey, i had a pfc boost controller hooked up in my old car but when i sold it i didnt remove all the parts for it. i have the thing that you plug the lines into but not the solenoid i think it is.

i'll get some pics of what i have in the morning, but i wanted to know is it possible to buy just that part that im missing or am i up for a whole new set?

also while ive got you here, my car was running fine untill a couple of days ago when i started to get heaps of knock, like jumping into the 90's at times. its fine if im just driving around normally but as soon as i give it a hit i get heaps of knocking. i thought maybe bad fuel but if refilled the tank since and same thing happening. nothing has changed in the car at all and ive had to wind down the boost to try stop some of the kock, was running 15psi and wound it back to 12ish. whats the go with that? spark plugs?

anyway thanks for reading my longest post ever :laugh:

Link to comment
https://www.sau.com.au/forums/topic/160317-pfc-boost-comtroller-parts/
Share on other sites

fiddlying around with the thing today, and i took it out with no air filter at all on it and knock was basically gone, only went to around 20. then i put my old pod on which is less restrictive and i had heaps less knock than with the apexi one ive got.

is it possible that the rubber tube running from the afm to the turbo is sucking shut, more so when i have a more restrictive intake? would this cause more kock?

when you took it out with no filter did you turn the boost back up to 15psi ?

the intake pipes standard have been known to suck in its a common problem

fiddlying around with the thing today, and i took it out with no air filter at all on it and knock was basically gone, only went to around 20. then i put my old pod on which is less restrictive and i had heaps less knock than with the apexi one ive got.

is it possible that the rubber tube running from the afm to the turbo is sucking shut, more so when i have a more restrictive intake? would this cause more kock?

i wouldnt run 15psi on a standard turbo either. but whats making me think maybe thats whats happening is the more restrictive the air filter is the more kock im getting, and i saw in the pod vs airbox thread that with the airbox being more restrictive it was sucking the pipe closed.

  • 2 months later...

well the car has been sitting in the drive way since april due to an unexpected trip to court (apparently speeding deserves more of a penalty than drink driving, stupid f**kers seriously but anyway) and i been thinking about the pinging how it just started happening.

maybe fuel filter is getting clogged? would that do it? or would that just make the fuel pump work harder.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
×
×
  • Create New...