Jump to content
SAU Community

Recommended Posts

HEY boys & girls

long story short.. i need a new engine... my car had an rb20det but yeah it died.. should i get another one.. for about $1000 or sh0uld i get an rb25det? they are newer, bigger & better lol ect.. how much more would i have to pay? $2500 for the rb25?.. has anyone got an rb25 for sale? :laugh: would it go in fine? no problems? :w00t:

and another thing.. i have about.. $3500 BUDGET :ninja: thats for the engine and install ..and prolly one of those major services ect. like timing belt and the oil and fluid top ups ect :rofl: lol i would shout u guys a carton and a good time if u wanted to meet up somwhere and do it all :laugh: i need to get in the circle of LOVE!

im lost without my r324door </3

haha does anyone have a flat bet tow trucK? ... just putting it out there :)

LUB JEZ <o/

Edited by 32JEZ
Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/
Share on other sites

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

following on from the PM's, I would recommend the Rb25 but not sure of whats needed in the gearbox department whether it bolts straight on or not.

3500 budget for a rb25?

nope... keep walking... you would ( while its open) replace any worn parts etc on the engine and possibly do the clutch at the same time ( since its all open)

for a rb25 ( + the ecu and wiring loom since the putahs are different) i would be looking at an upwards of 5000-15000

I got a few places to put a quote for me when i was thinking of putting an RB20//25 into my silvia and they broke down what needed to be done and what is reccomended..

they were not to far off each other and yah.. cheapest was 5000 and the most expensive was 15000 ( 15,000 was a complete rebuild + "bullet proofing" + after market gear)

So with your price range get an RB20 and do it right.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2977750
Share on other sites

3500 budget for a rb25?

nope... keep walking... you would ( while its open) replace any worn parts etc on the engine and possibly do the clutch at the same time ( since its all open)

for a rb25 ( + the ecu and wiring loom since the putahs are different) i would be looking at an upwards of 5000-15000

I got a few places to put a quote for me when i was thinking of putting an RB20//25 into my silvia and they broke down what needed to be done and what is reccomended..

they were not to far off each other and yah.. cheapest was 5000 and the most expensive was 15000 ( 15,000 was a complete rebuild + "bullet proofing" + after market gear)

So with your price range get an RB20 and do it right.

+ 1. normally all the wreckers sale for 5G.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978280
Share on other sites

I dont know much about the price ranges and acually bolting in the Rb25 but by the sounds of it, if you get a new RB20 and luckily you'll do it right and have some exra dosh over to get some nice upgrades.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978308
Share on other sites

stoking a 20 to a 24 is more effort than it's worth and it's not cheap anyway! With your budget, just stick to putting in a 20 again. You're going to have to pay someone to take it out, someone to put it all back in....and depending on where you go you'll use up your budget quicker than you probably think. Remeber he's not doing any of this himself....I assume? If you're LUCKY you'll have a bit of left over money for some bolt ons.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978673
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...