Jump to content
SAU Community

Recommended Posts

Hey fellow Queenslanders,

Just got myself a R34 2 weeks ago, took some pics today.

Extremly stock. not a thing done to it and very clean. Very happy with my purchase. Imported from Japan.

it even just had a standard tape deck.... btw for sale. stock tape deck. rare. dolby stero, $300 :blink:

The tape deck was the first thing that had to go. So I replaced it with a pioneer DEH-P9850BT.

The compliancers even left the xenons in for me :P .

Im located on the Sunny Coast, but drive down to brisbane a lot for work.

Here are some pics

post-49393-1211989569_thumb.jpg

post-49393-1211989665_thumb.jpg

post-49393-1211989747_thumb.jpg

post-49393-1211989854_thumb.jpg

post-49393-1211989919_thumb.jpg

Hey fellow Queenslanders,

Just got myself a R34 2 weeks ago, took some pics today.

Extremly stock. not a thing done to it and very clean. Very happy with my purchase. Imported from Japan.

it even just had a standard tape deck.... btw for sale. stock tape deck. rare. dolby stero, $300 :thumbsup:

The tape deck was the first thing that had to go. So I replaced it with a pioneer DEH-P9850BT.

The compliancers even left the xenons in for me :) .

Im located on the Sunny Coast, but drive down to brisbane a lot for work.

Here are some pics

post-49393-1211989569_thumb.jpg

post-49393-1211989665_thumb.jpg

post-49393-1211989747_thumb.jpg

post-49393-1211989854_thumb.jpg

post-49393-1211989919_thumb.jpg

i think i saw you about 3 on gympie rd.

nice ride

cheers

edit: same like urs butt with wing

post-49632-1212773320_thumb.jpg

Edited by naomy

Hey all...just became a skyliner the other week...R34GT (slow) 4 door (making it slower)

fully stock minus the heavy tint, exhaust, and lowering on 19inch advanti's...

Planning to follow 666dans steps into throwing in a turbine one day (waiting for more $)

Nice to see lotta 'liners on the southside....

-xcalibre

Hi all

New to the world of SAU

Owned a couple of skylines before, recently a R33 GTR V Spec and years ago a r31 silhouette.

I pickup my new toy next week, a black 32 GTR (can't wait)

Hope to see you cruising around

Also where does everyone meetup these days?

In Brisbane that is

Hi all

New to the world of SAU

Owned a couple of skylines before, recently a R33 GTR V Spec and years ago a r31 silhouette.

I pickup my new toy next week, a black 32 GTR (can't wait)

Hope to see you cruising around

Also where does everyone meetup these days?

In Brisbane that is

hey mick, welcome to the forum mate. 32 Gtrs all the way! haha. What part of brisbane you from? Every now and then people organise a dinner, cruise or track meet and so on in the Event forum. Keep an eye in there. Enjoy your stay

hey mick, welcome to the forum mate. 32 Gtrs all the way! haha. What part of brisbane you from? Every now and then people organise a dinner, cruise or track meet and so on in the Event forum. Keep an eye in there. Enjoy your stay

Hey hojak I'm on the westside and I'll keep an eye on the event forum

Would like to put a face to the car so to speak

I see so many crusing around and wonder if their on these forums

Any pics of your 32?

Go the 32 GTRs

Hey hojak I'm on the westside and I'll keep an eye on the event forum

Would like to put a face to the car so to speak

I see so many crusing around and wonder if their on these forums

Any pics of your 32?

Go the 32 GTRs

I'll show you mine if you show me yours... :laugh:

Was taken at a little meet we recently had last saturday.

dscn4876mckj1.jpg

Hi all,

:rofl:

I drive a 2003 M35 Stagea 250T RS four, mainly to and from work.... Sthsde Brissy always up for a burn an turn so if you see a reeeeally quick "Volvo" looking car shooting past, that could be me. i dont kno if anyone else owns one around here??? always keen for a drive and to go to any events an stuff around Bris vegas so invites welcome.

2003 Nissan Stagea with high flo turbo just installed, im looking now at wheels, exhaust, Sat Nav conversion, lowering, so if anyone knows a cool mob to help out please let me know as i have no idea what im doing!!

and how the hell do you get the TV to work....

Cheers

G

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...