Jump to content
SAU Community

Rb26 Head Porting

rb26s13

By rb26s13,
in Engines & Forced Induction

 Share

Recommended Posts

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
interesting, i stand corrected then... from what a fair few ppl told me the cost/gain ratio wasnt worth it but ill look into it... so how much are we looking at here to get an rb26 head ported?

A basic tidy up certainly isnt going to hurt thats for sure.

SK prices are pretty much there, you might be able to get to around 1k. It really depends on what needs to be done, and what does not

STATUS Grand Master

STATUS

Posted
Posted
dont trust the bogan shops up here with it..

also i dont think anyone up here actualy does porting

yeah there are some dodge dyno shops up there for sure, i can remember my last training trip up there.

180bfj20det Community Regular

180bfj20det

Posted
Posted (edited)
What a ported head should look like ----> http://www.skylinesaustralia.com/forums/in...howtopic=161673

Looks like a half port job to me.... You havent actually taken anything out which causes the majority of restriction. As soon as you get to the divider, this is where material comes out all the way to the valve seat. Inbetween those you have to determine how much material comes out for best flow according to the expected chacteristics of the inlet/exhaust pressure and velocity. I know the inlet looks like its nicely ported (no close up pics, hard to tell) but the exhaust, where the majority of the restriction is on an rb26 is as I said in my opening sentence.

Maybe SK will post a nice example of a ported head and if he doesnt, I wouldnt blame him. A lot of work is gone into finding out where to take material out for the best final port. Its not just remove 2mm all round.

Edited by 180bfj20det
DoughBoy Veteran

DoughBoy

Posted
Posted
Looks like a half port job to me.... You havent actually taken anything out which causes the majority of restriction. As soon as you get to the divider, this is where material comes out all the way to the valve seat. Inbetween those you have to determine how much material comes out for best flow according to the expected chacteristics of the inlet/exhaust pressure and velocity. I know the inlet looks like its nicely ported (no close up pics, hard to tell) but the exhaust, where the majority of the restriction is on an rb26 is as I said in my opening sentence.

Maybe SK will post a nice example of a ported head and if he doesnt, I wouldnt blame him. A lot of work is gone into finding out where to take material out for the best final port. Its not just remove 2mm all round.

Care to elaborate with specific facts? I take it you are quite familiar with RB head design and port flow, and know both what you are talking about with regards to RB heads and SK's henchmans capabilities.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      I forgot about my shiny new plates!
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...