Jump to content
SAU Community

Recommended Posts

OK pps

I have an R32 GTR - with near new excedy h/d clutch kit installed. It's been installed for about 5-6000 klms or so and it's been fine.

BUT

In the last week or so - I've been getting in intermittent hissing noise from inside the car ??

At first I thought it was coming from the air con – but even when it's off – I can still get the hissing

I've done some investigation - and I think it's coming from the clutch (peddle)

stop that laughing – I don't do drugs (any more :))

Form time to time (maybe once per day) - I can feel the clutch peddle go slightly heavy and then when I press the peddle I get a hissing sound coming from the foot well.

I can not hear it from outside the car (not a bearing) - and it's sounds like a air / vacuum leak coming from somewhere under the dash.

When it's doing it, I can literally just touch the peddle on and off (not actually engaging the clutch) and I will hear the noise. It will also keep hissing all the way through the travel of the peddle (all the way in and out) - told you it was not a bearing :D

then it just stops – and the peddle feel returns to normal

talk to me - am I hearing things ?

Link to comment
https://www.sau.com.au/forums/topic/161478-what-the-my-clutch-is-hissing-me/
Share on other sites

I believe GTR's run a vac booster for the clutch. Much like all the new nissan 4wd's do.

I'd say its stuffed. :)

Yep, I got the same problem. Been like that for a few months now. Haven't gotten round to fixing it. Not sure what long term effects it may cause - i've been assured there are none.

The GTR has a vacuum booster on the clutch. To temporarily stop the hissing you could disconnect the vaccum line that goes into the clutch booster and plug it - however your clutch pedal will become 3 times harder to engage.

To fix you need to replace vaccum booster.

Might be worth checking out a navara or something as the booster may be similiar and bolt up without too much trouble.

Wonder what Nissan would want new for a gtr item.... :S

Second hand + a heavy duty clutch its just a matter of when it does it again. Being 10-15yr old and all. :(

Does any one have pics of the booster? Its been some time since I've seen one and able to run out and check the Navara. Funny enough a few things on the navara are the same as the R32. :) The door latch mounted on the door frame is one that comes to mind. :(

  • 1 month later...

Awakening a dead thread...

Got this problem with my R33 clutch booster as well.

THe booster is located in the engine bay inbetween the firewall and clutch MC.

There is long term repercussions for not fixiing it. The nylon bushing in the clutch pedal will crush and wear out, then the pin will run directly on the pedal and wear the bushing hole and damage the pin.

I fixed my bushing issue by machining a brass one up, then found this thread which explains why its happened in the first place!

Cheers,

Ian

I have an R32 GTR and it had the exact same problem. It was making a hissing noise when you push in the clutch. I got it fixed sometime last year and it's not a big thing. I think the part cost $120 or so and was charged maybe $60 for labour? Once it was done the pedal was lighter to push down on and I guess if it's vacuum assisted you know when it's really stuffed when you have to push alot harder to get it working.

I would say most mechanics in brissy can replace it fairly easy for you I got it done at a local mechanic no problems.

GL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...