Jump to content
SAU Community

Opinions On This Colour

NISMO

By NISMO,
in General Automotive Discussion

 Share

Recommended Posts

NISMO Grand Master

NISMO

Posted
  • Author
Posted (edited)
6624953.jpg

This BLUE would be a different story though :( Its on carsales in NSW under dealer cars..there's quite a few in Australia at the moment..might be worthwhile looking interstate as well instead of straight from Japan.

That's the same blue I think.

Looks really good there, but again I've seen it in some shots on a dull day and it looks quite dull.

As for looking here, would love too, but current prices are on average 10k more than what it would cost to get the car from Japan.

eg a 2005 auto went for just over 2mil yen last week. That's around 36k ready to drive, rego and all. On sites like carsales a 2005 auto is going close to 50k. Big difference!

Edited by NISMO
n15m0 Grand Master

n15m0

Posted
Posted
That's the same blue I think.

Looks really good there, but again I've seen it in some shots on a dull day and it looks quite dull.

You reckon? This one looks more like bayside blue to me...I could be wrong..bloody sun :( I have seen one in bayside blue in the flesh before and looks way hot!

NISMO Grand Master

NISMO

Posted
  • Author
Posted
You reckon? This one looks more like bayside blue to me...I could be wrong..bloody sun :( I have seen one in bayside blue in the flesh before and looks way hot!

yeah pretty sure, the Carribean blue is the only colour close to that, the other blues they came in were quite different, Check out the front bumper, it's quite close to the other pic.

JUNR34 Community Regular

JUNR34

Posted
Posted

Mate IMO just take your time and find one with the colour you really like, for me I would go for black as well. Cause somewhere down the track say if you're not happy with the colour a respray aren't going to be cheap haha. Also just import it from Japan since you can find these in mint condition, you can get a nice set of 18s from the money you save.

SS8_Gohan Grand Master

SS8_Gohan

Posted
Posted

^ i like that idea. Save money by importing, use saved money on some 18" hotness.

black FTW. Saw one in the states with the kit, little rear spoiler, etc... looked awesome i must admit

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...