Jump to content
SAU Community

Recommended Posts

Hi mates,

I want to know what is the maximum (safe) power i can get with those ijectors along with fuel and turbo..etc mods i have..RB25DET:

HKS 555cc injectors

walbro 255

stock rail

sard standard reg

greddy t78

HKS 1.2mm metal head gasket

stock internals

pfc

what boost do you suggest to stay in the safe side???

Edited by Light
Link to comment
https://www.sau.com.au/forums/topic/163612-hks-555cc-injectors/
Share on other sites

040 is internal

no part no#, do a search

injectors, are injectors, as long as they work

boost no idea, the compressor map determines that

that compressor will dial in a fair amount of airflow

i woudlnt be going near 300rwkw with std internals

it will go bang. can u afford a rebuild

what do mean "injectors are injectors"

dont they have a maximum that at a specific point of boost they will stop being sufficient??

I think so but please correct me if i am wrong

and what is maximum hp/kw stock rb25det internals can hold?

injectors have nothing to do with boost

they can only flow so much, that is 555cc per minute

should get u upto maybe 350rwkw so they are fine

stock internals i wouldnt go past 280

even thats pushing it, depends on what u do and how u drive it

Id stick to around 250rwkw if you would like the engine to last. Regular servicing and not thrashing it to death you should see it to be quite reliable. If you dont get forged rods, pistons and really make use of the power that turbo can make its pointless to have such a large turbo when you could have alot more responsive set up making the same power.

The T78 is a tad oversized for the stock rb25t.

Realistically 250-260rwkw is a nice reliable number but 300rwkw can be done providing its tuned well and the static comp dropped a tad via a thicker headgasket.

Either way.. the T78 is oversized. lag lag lag when you don't really need to have for that power level.

Just look around on the forum and take not what others use, then do a Google for prices.

Look in the traders for sale section and see what specials they offer.

Pistons avg $1300, Rods $800 and about an extra $3000 to do it properly......

Light depending on what you are going to use the car for I would be thinking realistically how much traction can I get at best and will the drive line stand up to the power delivery - let alone the pistons rods and crank . It sounds like a can get a big turbo situation and may end up starting here and spending a fortune by the time you reach the other end of the car mods wise . If you don't have the T78 or the budget to build an 800 Hp capable car I reckon I'd be looking for a turbo that would keep you within at least the practical and affordable limitations of the driveline starting at the fan and ending at the tyres .

For the 250 + RWKW that you can probably get to the ground through sane street rubber a Hi flow or a real GT3071R done right WILL be streets ahead . Night and day .

Your call , cheers A .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...