Jump to content
SAU Community

Car Won't Rev ! Help

dOOb

By dOOb,
in Engines & Forced Induction

 Share

Recommended Posts

dOOb Enthusiast

dOOb

Posted
Posted

G'day guys, i own a ca18det 180sx.

i need more ideas of how to fix this problem, basically car won't stay running without my foot on the accelerator, and when i do it won't rev pass 900.

i've changed the spark plugs, test the coils, did a compression test (all good), cleaned the most of the adaptors.....

is there anything else i should do to to get this car on the road again?

Link to comment
https://www.sau.com.au/forums/topic/163986-car-wont-rev-help/
Share on other sites
dOOb Enthusiast

dOOb

Posted
  • Author
Posted (edited)

not wanting to sound rude but what could be wrong with the afm? i did took the thing off and gave it a quick cleaned, and from inspection,i thought the thing doesn't have too much mechanical components nor electrical components for it to be related to any problem.

as for the intercooler, while carbie cleaning the throttle body, i did took some of the IC pipes off to clean off some of the oil, i remember i did tighting up all the clamps but will pull it apart and pull it back together again tomorrow.

uummm at this point i gonna say no to a new comp :) wallet is quiet empty now after easter.

by any chance could be related to the crank sensor?, cos i got it replace a few days before this rev problem

This happen a day after i degreaser the engine, but i did took the car out after i cleaned it, and it was fine

Edited by dOOb
dOOb Enthusiast

dOOb

Posted
  • Author
Posted (edited)
Check your intake piping, I popped off a pipe today and it did exactly as you described it. Won't rev and dies if you lift the foot off the accelerator.

took all the pipes of today and put it back today nothing change so................

Is the CAS tight?

It might not be on tight enough and the timing is way out.

Check your connections on EVERYTHING electrical too. Just unplug them, and plug em back in.

........i messed around with the crank sensor, i didn't take it off just losen the bolts and turned it in both directions a lil bit at a time. NOW THE DAME THING DOESN'T EVEN KICK OVER.

CAS was tight, timing is okay after i changed the crank sensor, i've already unplugged most of the adaptors and cleaned it with carbie cleaner.

ANYBODY GOT ANYMORE IDEAS?

Edited by dOOb
dOOb Enthusiast

dOOb

Posted
  • Author
Posted
try a fuel pump. i replaced one in a r33 that was doing the same thing fixed the prob

i checked the fuel pump when i changed the "O ring" on top of the fuel tank about 6 weeks ago, fuel pump looks to be near new, also checked the fuel pressure and thats okay aswell.

thanks for that tip SXC_R33, can anybody think of anything else that is causing this problem?

unarmed_skyline Experienced

unarmed_skyline

Posted
Posted

+1 afm is stuffed actually a really common failing part and it wuold make the car not run past about 900rpm but you should be able to start the car fine, try starting the car with it unplugged if its worse its probably ok but if its the same then it could be stuffed

WazR32GTSt Grand Master

WazR32GTSt

Posted
Posted

its entirely possible that its the AFM as stated, and because its been running rich for so long you have simply fouled the plugs...

i'd say get a new set of plugs ($20 all up for NGK copper BCPR6ES) and get a hold of someone's AFM

change them both at the same time and see if it kicks over and runs ok

hope that helps

dOOb Enthusiast

dOOb

Posted
  • Author
Posted
+1 afm is stuffed actually a really common failing part and it wuold make the car not run past about 900rpm but you should be able to start the car fine, try starting the car with it unplugged if its worse its probably ok but if its the same then it could be stuffed

seeing how i've stuffed around with almost everything i can think of, next will be the AFM, will try it unplugged or swap it with a mate.

its entirely possible that its the AFM as stated, and because its been running rich for so long you have simply fouled the plugs...

i'd say get a new set of plugs ($20 all up for NGK copper BCPR6ES) and get a hold of someone's AFM

change them both at the same time and see if it kicks over and runs ok

hope that helps

i've already changed the plugs when this problem first occured, but that didn't much to it but might changed to those recommended to see if theres any different.

WazR32GTSt Grand Master

WazR32GTSt

Posted
Posted

yeah but what i'm saying is that the AFM is the cause, and the plugs are fouled because of the AFM

so a new AFM might fix the cause, but the car might not start still because the plugs are foulled

you have to fix the cause (AFM) and the effected parts (plugs) at the same time to see if this is in fact the case

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...