Jump to content
SAU Community

R33 Powerfc Map Sharing Thread

benl1981

By benl1981,
in Engines & Forced Induction

 Share

Recommended Posts

benl1981 Grand Master

benl1981

Posted
Posted

I'm starting this thread so there is somewhere to compare maps..Not sure if this has been started already somewhere else.

I have a GCG high flow that has some hesitation/misfire when backing off slowly. SK said that it is common to have to increase ignition advance by 10 to 15 deg over the default maps at certain load points in order to get the 450hp turbo to run smoothly on the Rb25.

I am after someone with either stock turbo and tuned precisly or someone with a GCG high flow and stock AFM to share there maps so I can drive it for a while before I get a tune as I still have to add a few mods.

I have been playing around a bit but it's easy to get too much knock..with the stupd hand controller and driving it makes it hard. I don't have datalogit so if anyone has the maps in .xls (excel) it would be good.

I remember Paulr33 did quite a bit of work with adding advance to the first 10 x10 lot of cells..

THanks!

Link to comment
https://www.sau.com.au/forums/topic/164117-r33-powerfc-map-sharing-thread/
Share on other sites
Cubes Grand Master

Cubes

Posted
Posted

The car should run fine on the base map with regards to general commuting.

Paulr33 playing with the first 10x10 maps only alters the cruise and 'very' light throttle acceleration.

If your having hessitation/backfire when backing off the issue isn't cause by the turbo, check your tps is set correctly and the car isn't running overly rich. Ensure your getting reasonable economy, which is 400km's+ per tank when driving it normally with the odd squirt. If your getting sub 400's then start looking at the AFM, O2 sensor & injector condition.

With regards to knock pull a good 6-7degree's. If it still knocks you may very well be knocking due to it running lean.

So be carefull.

benl1981 Grand Master

benl1981

Posted
  • Author
Posted (edited)

Its hesitating when easing off the throttle - not when fully off it.

Maybe at some low load points it is also..i.e. at low revs medium load.

Fuel economy is still the same. I have only changed the turbo - nothing else.

Edited by benl1981
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

where are you ? if your around sydney / newcastle area and your interested in getting it tuned i am tuning a R33 Power FC on sat arvo on a guys car that i installed a KKR turbo on last weekend and will have the tuning gear (power fc laptop software and wide band sensor)

Let me know if your interested in getting it done

Revhead Grand Master

Revhead

Posted
Posted

If you haven't already, double-check the mechanical side - make sure hoses are tight etc. There's no point trying to tune out a problem that isn't related to tuning :)

Assuming you've already done that, you could try this. It's been a while so I can't remember what it's called, but there's a screen on the PFC named something like "map browser" - it shows a 20x20 matrix with a dot on it, indicating which part of the maps you're currently using. Take your car for a spin and have someone watch that screen, and have them note where the marker is when the car starts to miss. Clean up the fuel/ign maps around the area indicated by the marker. It gives you somewhere to start anyway.

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

you mean the map tracer - monitor - map trace

If you haven't already, double-check the mechanical side - make sure hoses are tight etc. There's no point trying to tune out a problem that isn't related to tuning :)

Assuming you've already done that, you could try this. It's been a while so I can't remember what it's called, but there's a screen on the PFC named something like "map browser" - it shows a 20x20 matrix with a dot on it, indicating which part of the maps you're currently using. Take your car for a spin and have someone watch that screen, and have them note where the marker is when the car starts to miss. Clean up the fuel/ign maps around the area indicated by the marker. It gives you somewhere to start anyway.

  • 9 months later...
Devils_Advocate21 Mentor

Devils_Advocate21

Posted
Posted

That was last year, n e way, in regards you got to remember the time and money put in for such maps n e way from reputable tuners and such, i dare doubt some people would want to share there maps due to money basis, Not only that is that there is so much variance between cars these days, it would still need to be touched up or re done by a tuner n e way...

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • dawhitehonky
      M35 Aftermarket Fuel Pump

      By dawhitehonky · Posted

      I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • GTSBoy
      Rapid-fire squeaking/creaking from rear suspension

      By GTSBoy · Posted

      Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...