Jump to content
SAU Community

Problem With My R34 Gtt

ND834
 Share

Recommended Posts

ND834 Rookie

ND834

Posted
Posted

One day.. just cruzin along on the Anzac bridge something wierd happens. Suddenly the Oil, TCS, Slip light comes on my dash

and wont turn OFF!!(Until i turn off the Engine) It happens couple of times a week~! There's nothing wrong with my driving..

and the cars stock(19inch,lowered,exhaust and air filter). Does anyone know what this problem is?? :closedeyes:

post-33188-1177118809.jpg

Link to comment
https://www.sau.com.au/forums/topic/165459-problem-with-my-r34-gtt/
Share on other sites
n15m0 Grand Master

n15m0

Posted
Posted

Does ur car do anything funny when the warning lights come on? Could be anything from faulty coilpacks to O2 sensor etc...best way is to find a workshop with a Nissan Consult machine, they plug it in your car and will be able to pinpoint what the error is and what needs replacing.

There is a thread on here that teaches you how to do it urself but if ur not game, then leave it to the experts but definately get it looked at quick smart.

Mine did this too when I first got it, turned out it was a faulty o2 sensor..

R34NRG Grand Master

R34NRG

Posted
Posted (edited)

i dunno but im a lil worried wen ur oil, TCS and slip are all on.

maybe ur losing oil somewhere which is causing your car to lose traction thus the slip.

lol good luck mate sounds like a lil bit of a screw around.

ur best bet is to bring it to nissan or a machanic and let them to a dionostics(sp?) test

Edited by anDru
smurf80 Experienced

smurf80

Posted
Posted
i dunno but im a lil worried wen ur oil, TCS and slip are all on.

maybe ur losing oil somewhere which is causing your car to lose traction thus the slip.

lol good luck mate sounds like a lil bit of a screw around.

ur best bet is to bring it to nissan or a machanic and let them to a dionostics(sp?) test

hahahahaha

MRR34 Rising Star

MRR34

Posted
Posted
Does ur car do anything funny when the warning lights come on? Could be anything from faulty coilpacks to O2 sensor etc...best way is to find a workshop with a Nissan Consult machine, they plug it in your car and will be able to pinpoint what the error is and what needs replacing.

There is a thread on here that teaches you how to do it urself but if ur not game, then leave it to the experts but definately get it looked at quick smart.

Mine did this too when I first got it, turned out it was a faulty o2 sensor..

Same thing happen to me turns out it was my No.3 coilpack .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...