Jump to content
SAU Community

Recommended Posts

Well guys im finally looking at getting my car back on the road.....

Its been sitting in my shed literally unused and unrun for just over 2 years now. The reason behind this is i took a traineeship and blah blah so i could get ahead in life cash wise, well i am ahead now and im gonna get this baby back....

What i wanna know is considering it hasn't been run or used for SO long (surprisingly all the tyres aint flat!) what will i need to check over before taking her out on the road safely as i dont particularly want to be a danger to myself, my car and especially others.

Now im assuming, timing belt, oil, g/box oil, water pump (maybe?), front and rear diff, fuel hose?, fuel lines, brakes?

If there is anything please let me know, thanks guys!

Also by the way the car is a 93 R32 GTS4

Cheers

Maybe change the belts.because they are rubber and they have been still for so long.

Look for cracks,rips/tears general signs of wear.If they are not nearing 80K done on them,if they were not exposed to rain and the elements id say the belts will be k.Look at them give them a wiggle and see if they crack or not.

Dont worry about the water pump straight away.it might still be allright.But if it leaks you know it's time to change it.

Any1 feel free to proove me wrong.

You shouldnt have left the car,and not turned it over at least once a month for a warm up.

Mine was off the road for 1.5yrs.But turned over once or twice a month.the same belts,bar the timing belt,were left on and they had been going strong up untill last week.

So i did the oil and filter,brake fluid,timing belt,diff and gearbox oil,new radiator water.Water pump(tho it did need changing) urs may not.

PS:start the car up on a flat surface seen as tho it has sat for so long the oil will most surely be at one end of the motor.

nothing, just fire it up and drive. No different to my car that was sitting in the garage for half a year doing the turbo.

when your car came over from japan, it coudl have been sitting in a holding yard for months. The wharfies would have prepared your car for driving by cold starting it and ripping a burnout at the rev limiter off the boat.

Edited by MANWHORE
nothing, just fire it up and drive. No different to my car that was sitting in the garage for half a year doing the turbo.

when your car came over from japan, it coudl have been sitting in a holding yard for months. The wharfies would have prepared your car for driving by cold starting it and ripping a burnout at the rev limiter off the boat.

I love this guy's responses.

If your paranoid when remove the plugs, disconnect the cable that goes to the crank angle sensor, and crank the motor till you see oil pressure, refit plugs and cas wire, and away you go. Best to do this as there would be no oil anywhere.

If your paranoid when remove the plugs, disconnect the cable that goes to the crank angle sensor, and crank the motor till you see oil pressure, refit plugs and cas wire, and away you go. Best to do this as there would be no oil anywhere.

Agreed, but i would first change all fluids. It's easy to do for peace of mind.

If your paranoid when remove the plugs, disconnect the cable that goes to the crank angle sensor, and crank the motor till you see oil pressure, refit plugs and cas wire, and away you go. Best to do this as there would be no oil anywhere.
Agreed, but i would first change all fluids. It's easy to do for peace of mind.

best to listen to these guys mate, you will have 0 oil pressure as the oil would have come off the bearings of your motor as well as your turbos. i wouldnt turn the car on unless the gauge started reading oil pressure from cranking it (pulling CAS out and turning key).

nothing, just fire it up and drive. No different to my car that was sitting in the garage for half a year doing the turbo.

when your car came over from japan, it coudl have been sitting in a holding yard for months. The wharfies would have prepared your car for driving by cold starting it and ripping a burnout at the rev limiter off the boat.

dont listen to this guy. just because someone MAY have treated your car like shit, doesnt mean you need to.

don't listen to this guy...

Don't listen to any of em man :blink:

Procedure:

Wait 20min after a meal ( just like mum said b4 swimming), Replace oil, check brake / slave cylinder oil, tyres belts for cracks, coolant, disconnect CAS, crank till pressure, reconnect CAS. While its idling for 2 -3 mins while revving gently, smack yourself in the face for not driving it in so long, check you got your granny nappy on, beep the horn to arouse the stoned hippy off your bonnet and call 000, realing off that theres an "officer down" 40clicks east of your favorite stretch of road ... its Skyline Time!!!!!

joe, i was being slightly sarcastic about the wharfies. My message wasn't totally sarcastic though.

What I was getting at, is people often go team extreme just because of the fact that a car has been sitting there for a little while.

Fuel - will go off, so i'd drive easily until i can refill again.

oil - oil guru websites have generally said that there is no difference between oil sitting in your sump and in a bottle. If it was new before you left it, then it's still new.

filter - why would it go off

coolant - needs to be changed every 2 years anyways.

diff and gbox oil - refer to oil above. I'd like to further add, that gearbox and diff oil needs to be changed even less frequently than engine oil, so it's even less of a concern than the engine oil.

pas fluid - same.

belts - should be fine.

I do agree with disconnecting the cas and giving it a crank though - get some oil flowing before you start it.

I also agree with starting it and letting it warm up - should always do that anyways

Edited by MANWHORE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...