Jump to content
SAU Community

Recommended Posts

Your post is totally useless in helping people help you diagnose your problem. Perhaps if you outline what you've done. e.g. whether it's a new engine swap, or whether you bought it like that, whether it's ever started, whether you have or think you've done anything stupid or dodgy etc.

Spray some nulon brand 'start ya bastard' into it

Edited by MANWHORE
Link to comment
https://www.sau.com.au/forums/topic/167250-please-help/#findComment-3098479
Share on other sites

so i purchased the car with the swap already in it, it was running fine when i got it then it started to idle funny and die at random, so my brother thought it might have a plugged fuel filter in the processe of checking it out he dropped it on the headers and my whole engine bay went up in flames i put the fire out and the insurance company "fixed" it after about 8 months of fighting with them and the shop that was supposed to be working on it. when i got it back it can poorly it hunts durring idle untill it wwarms up and then evens out at about 750rpm it also surged under boost now. about a month ago it kept dieing so i checked the spark plugs and they where covered in black what seems to be carbon which im asumeing is from it running to rich, so i changed the plugs out. after about 15km of run time i parked my car and i havent sarted the car for a while the other day i started it up and it hunted like usuall then just died. since it has died i have changed out the vacuum lines other then that i have no idea why it wnt start it cranks there is fuel getting to the fuel rails my ECU is turning on but it just wont start the plugs are aleady black again but the tips are still cleanish and should spark. i hope this is a little better info on this cars history and some one can help me figure out what i need to do to get it running again

thanks Brent

Link to comment
https://www.sau.com.au/forums/topic/167250-please-help/#findComment-3098857
Share on other sites

so today i sand blastd my plugs and after about 10 min it the car finally turned over and started but only ran for a couple of seconds then died again and wouldn't start again after that... is it possible that there is a faulty sensor that would cause this because i have fuel and i have spark the only thing i have not yet checked is compression but im wondering if theres anything else that could cause this

Link to comment
https://www.sau.com.au/forums/topic/167250-please-help/#findComment-3099977
Share on other sites

It sounds like the fuel pump is losing power as soon as the key returns to "ON". Even if you had poor compression, the engine would still run once it started.

You need to fit a fuel pressure gauge to confirm that the pump and FPR are working correctly.

Link to comment
https://www.sau.com.au/forums/topic/167250-please-help/#findComment-3100080
Share on other sites

i can hear the fuel pump turning on once i turn the key to the on position but now that you say that it does seem to turn on and keep running for a longer period of time then usual once i turn the key to the on position i can hear it for probly about 15-20 seconds ill try and see if thats the problem thanx ill keep everyone posted on the progress

Link to comment
https://www.sau.com.au/forums/topic/167250-please-help/#findComment-3100422
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...