Jump to content
SAU Community

Recommended Posts

i have been told the "SLIP" is for traction control and flashes sliding but when does the "4WD" gets used? i thought it uses it when you loose traction in the back wheels and then uses the fronts like the GTR.it has never been used yet.does it get used when it looses complete traction with the back wheels?

Link to comment
https://www.sau.com.au/forums/topic/16757-gts4slip-and-4wd-lights-near-speedo/
Share on other sites

since i own a gts4 ill help out

it has no traction control, its just a slip warning light, cause sometimes your slipping and you dont even know it

4wd is working 100% of the time

so if all goes well you should never see the 4wd light

the only bad thing bout those lights is i cant find the illumnated dials to fit the gts4

the 4wd isnt working all the time

the car has a eletric senser that throw the power to the frunt wheels as the harder u punch the right foot the more power gos for wood thats y u can pull out the fuse and dino the car on a 2wd dino if it was 4wd all the time u wood not b a bell to do this well thats haw a r32 gts4 is set up dont no haw the 33 is

Originally posted by Ryan D

it has no traction control, its just a slip warning light, cause sometimes your slipping and you dont even know it

got that right, once on a wet night on a long straight stretch on the freeway doing 140 on fifth, when the slip light come on...wtf? real spooky...didn't even know there's any wheelspin...probably very mild. took it easy after that...

the 4wd isnt working all the time

the car has a eletric senser that throw the power to the frunt wheels as the harder u punch the right foot the more power gos for wood thats y u can pull out the fuse and dino the car on a 2wd dino if it was 4wd all the time u wood not b a bell to do this well thats haw a r32 gts4 is set up dont no haw the 33 is

-

Wouldnt that require a variable diff? im pretty sure is all time 4wd

cause many people have told me that it is. and it sure handles like it is. Cause even at top speed i can fly round sweeping bends that are a little harder than average

Doesn't the R33 GTS4 have a torque-split gauge? The R32 version certainly does - it indicates how much torque is being applied to the front wheels. Most of the time, it sits on '0'.

The Nissan 4WD system uses G-sensors and the ABS sensors to determine if / when any power should be fed to the front wheels, either because of wheel slip (ABS) or acceleration loads (lateral / longitudinal G-sensors)

The transfer case has a hydraulic clutch fed from the reservoir in the boot (RH rear corner), to apply 4WD as required.

R33s (GT-Rs at least) tend to go to a sort of limp-home mode if you pull the 4WD fuse.

If the R33 is anything like the R32, then you can't simply bolt a RB25DET from a RWD in the 4WD version. In the R32, the sump pans are different between the RWD and 4WD versions of the RB20DET engine, I'm just guessing the same with the R33, but I could be wrong.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...