Jump to content
SAU Community

Recommended Posts

Just a tid bit of advice. While first thought would be that the funnelling of all that surface area into a relatively small diameter hole will give you lots of airflow to the brakes/rotors. it probably wont. Most likley you will get a lots of turblulence and reduced airflow. (also increases sc)

Be interesting to see how it goesss. but i would think you are better with a flush panel, whereby helping the cd of the car...and having an opening essentialy the same diam as the duct you are going to run. Its normally the best compromise.

Roy,

All fair points mate and i do tend to agree with you. The reason for them being so big is that i am going to run another duct from each fibreglass panel to the other side of the rotor, the ones you see are for the caliper. I thought that 2 would be better than 1, just waiting on more ducting to arrive.

The inlet you see is 75mm so not small but not huge either. I also do test how much air i get through these with my big f#$& off fan that we use to cool the car down after each run as the pit garages are air conditioned it helps cooling everything down under the car, pic below

The reason is that we do run in temps over 40, yesterday was 46 while i was doing this mod near killed me.

post-28646-1178418132.jpg

was a problem point and still not where i would like it.

Last time out i ran with the alloy radiator, standard fan, no shroud and a N1 water pump, ambient was 40 degree and i was a little hot with both the after market temp gauge in the engine out let and the Power FC both showing 96 max. Still a bit hotter than i would like but its really too hot to run these cars at that temp, intake temps and knock are the pits mate.

need to update my other thread on this topic too

Yer thanks but i still have top put put the second inlet in the duct and it was easier to do with the front bar back on the car. not to mention quite a bit of filler to put in and sanding to do as you can see

Edited by tacker

nearly finished still have to run two more ducts back to the fronts but made a real difference to the rotor temps and brake pads. No more white edges on the pads any more. and then some better rear ones and thats it

  • 2 weeks later...

Got my act together last night and finished the running of the brake ducts to the font brakes last night.

Also as an after though i put in some CAI which i hope will work, i guess it got to help.

post-28646-1180318959_thumb.jpg

post-28646-1180319008_thumb.jpg

post-28646-1180319079_thumb.jpg

Interesting setup.. I'd be interested in whether channeling the air into such a small defined space is any better than the general flow effect over the wider area.. e.g. just removing the splash guards and allowing the air to pass through.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...