Jump to content
SAU Community

Recommended Posts

Just a tid bit of advice. While first thought would be that the funnelling of all that surface area into a relatively small diameter hole will give you lots of airflow to the brakes/rotors. it probably wont. Most likley you will get a lots of turblulence and reduced airflow. (also increases sc)

Be interesting to see how it goesss. but i would think you are better with a flush panel, whereby helping the cd of the car...and having an opening essentialy the same diam as the duct you are going to run. Its normally the best compromise.

Roy,

All fair points mate and i do tend to agree with you. The reason for them being so big is that i am going to run another duct from each fibreglass panel to the other side of the rotor, the ones you see are for the caliper. I thought that 2 would be better than 1, just waiting on more ducting to arrive.

The inlet you see is 75mm so not small but not huge either. I also do test how much air i get through these with my big f#$& off fan that we use to cool the car down after each run as the pit garages are air conditioned it helps cooling everything down under the car, pic below

The reason is that we do run in temps over 40, yesterday was 46 while i was doing this mod near killed me.

post-28646-1178418132.jpg

was a problem point and still not where i would like it.

Last time out i ran with the alloy radiator, standard fan, no shroud and a N1 water pump, ambient was 40 degree and i was a little hot with both the after market temp gauge in the engine out let and the Power FC both showing 96 max. Still a bit hotter than i would like but its really too hot to run these cars at that temp, intake temps and knock are the pits mate.

need to update my other thread on this topic too

Yer thanks but i still have top put put the second inlet in the duct and it was easier to do with the front bar back on the car. not to mention quite a bit of filler to put in and sanding to do as you can see

Edited by tacker

nearly finished still have to run two more ducts back to the fronts but made a real difference to the rotor temps and brake pads. No more white edges on the pads any more. and then some better rear ones and thats it

  • 2 weeks later...

Got my act together last night and finished the running of the brake ducts to the font brakes last night.

Also as an after though i put in some CAI which i hope will work, i guess it got to help.

post-28646-1180318959_thumb.jpg

post-28646-1180319008_thumb.jpg

post-28646-1180319079_thumb.jpg

Interesting setup.. I'd be interested in whether channeling the air into such a small defined space is any better than the general flow effect over the wider area.. e.g. just removing the splash guards and allowing the air to pass through.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...