Jump to content
SAU Community

What Am I In For?

Gazzilla

By Gazzilla,
in Victoria

 Share

Recommended Posts

SKY031 Grand Master

SKY031

Posted
Posted

Don't stress Ash, I get it.

...it seems that one of the questions has since been edited to make it a bit more clear :(

i live in sydney - so i don't know if these rules differ from state to state.

Yes, they do.

If you live in Sydney, go and ask for info in the NSW section so that you can get the information which relates to you.

No point in changing everything if you don't have to.

habibz_r33 Collaborator

habibz_r33

Posted
Posted (edited)

this sucks! i have exactly the same problem in my r33 gtst, when i got pulled over on sydney rd coburg, the cop took a photo of my engine bay when he saw my BOV and said thats bad news 'expect a letter from EPA' and bye. i asked if that was legal for him to take a photo, and he said nothing just 'wait for a letter and you will be told wat to do' and he left like that. 2 weeks later i got the letter and after asking for an extension due to work and wasnt approved cause my letter for extension was too late now i have a suspended rego too, so cant even drive it.

i have a HKS BOV, 4inch exhaust, turbo timer, boost controller, intercooler, but no pod and i need to replace them with standard parts very quickly cause its due at EPA on the 29th of may, so if anyone can help that would be great, i will gladly swap my parts with stock BOV and exhaust with cash difference. i wont ask for much depending on condition, as my BOV and exhaust are still in good condition. so please help it will be gladly appreciated, my number is 0421 795 757. SAM

cheers

Edited by habibz_r33
ghostflameR33 Enthusiast

ghostflameR33

Posted
Posted

Have you tried ringing up the epa, or going on the epa websites and getting the pdf download on all the modifcations you are allowed to have etc. It's all stated on there website. And yes they do check your car thouroughly. i put mine back to full standard as it was out of the factory. they plug a computer into ur car which checks all the settings for carbon monoxide etc. The guy there is good to not as bad as you would think.

Spunky Munky Grand Master

Spunky Munky

Posted
Posted

Sounds way too usual.

The copper is right, you can only have 1 air induction mod. There's no way you will lose your intercooler, right? Hence, just source a standard airbox from somewhere and get rid of the Pod filter. Pod filters (unless enclosed and a proper CAI is employed is shit-house as it sucks way too much hot air from the engine anyways), BOV has to go, if you have a turbo controller that has to go to.

The copper should have given you a nice yellowy canary - just follow that. After you've demoded everything, go get a full RWC done, then bring it to a VICROADS office, they will inspect your vehicle then will stamp the canary as APPROVED and then you're free again.

With the EPA, letters take around 3-5 weeks to arrive - as you know the EPA deals with the environment and bullshit like that - so they are only concerned with your exhaust - you will have to get a smaller exahust. After you do this, bring it to their office (as per the EPA letter) , again they will check, measure etc then if you pass, they will stamp off the letter and give you a receipt of compliance - and that's it. the end of the story.

That's why I say to everyone, do not mod your vehicle until you get it cleared by someone (prefferably VICROADS) that it is legal etc OR get a qualified engineer and get them to write you up a government-approved engineers certificate (will cost heaps, around $650?). So yeah, just watch out next time mate...

Ronin 09 Grand Master

Ronin 09

Posted
Posted
With the EPA, letters take around 3-5 weeks to arrive - as you know the EPA deals with the environment and bullshit like that - so they are only concerned with your exhaust - you will have to get a smaller exahust. After you do this, bring it to their office (as per the EPA letter) , again they will check, measure etc then if you pass, they will stamp off the letter and give you a receipt of compliance - and that's it. the end of the story.

If it's only an exhaust noise test - then an authorised exhaust shop can do the noise test. They don't care about all the other mods, just that it is under the legal limit.

If it's a full blown EPA test - wrong info. EPA are interested in all things that may affect emissions - cams, turbos, intercoolers, pods, afms, computers etc etc.

so you can't just rock up with a FOT and a factory exhaust and it'll pass. Factory everything (except one intake mod) is the order of the day. Good luck if this is the case.

That's why I say to everyone, do not mod your vehicle until you get it cleared by someone (prefferably VICROADS) that it is legal etc OR get a qualified engineer and get them to write you up a government-approved engineers certificate (will cost heaps, around $650?). So yeah, just watch out next time mate...

Vicroads wouldn't know their a$$hole from their earhole. No good asking them if it's "legal" to mod it. Read the legislation and interpretive explanations (and guidelines) - that's the law and it can't be changed. Don't ring em and ask them - the person on the other end of the phone doesn't care or know.

Also, an approved Vehicle Engineer still won't approve something that in their opinion is not safe - eg cutting the front reo to fit a FMIC.

Note to all - check all state legislation before modifying, at least know what you are getting yourself into.

Gazzilla Experienced

Gazzilla

Posted
  • Author
Posted
Sounds way too usual.

The copper is right, you can only have 1 air induction mod. There's no way you will lose your intercooler, right? Hence, just source a standard airbox from somewhere and get rid of the Pod filter. Pod filters (unless enclosed and a proper CAI is employed is shit-house as it sucks way too much hot air from the engine anyways), BOV has to go, if you have a turbo controller that has to go to.

The copper should have given you a nice yellowy canary - just follow that. After you've demoded everything, go get a full RWC done, then bring it to a VICROADS office, they will inspect your vehicle then will stamp the canary as APPROVED and then you're free again.

With the EPA, letters take around 3-5 weeks to arrive - as you know the EPA deals with the environment and bullshit like that - so they are only concerned with your exhaust - you will have to get a smaller exahust. After you do this, bring it to their office (as per the EPA letter) , again they will check, measure etc then if you pass, they will stamp off the letter and give you a receipt of compliance - and that's it. the end of the story.

That's why I say to everyone, do not mod your vehicle until you get it cleared by someone (prefferably VICROADS) that it is legal etc OR get a qualified engineer and get them to write you up a government-approved engineers certificate (will cost heaps, around $650?). So yeah, just watch out next time mate...

Ok thats handy advice.. But DO i have to go through the whole Ordeal with Vicroads??? when i purchased the car, the previous owner went and got a roadworthy done, and that was roughly 2.5 months ago, So i have to do all that shit again?? If Vicroads cleared this car as roadworthy less than 3 months ago. does it not Override what ever the hell the EPA say?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
    • MBS206
      remote oil cooler hose size, 8,10 or an12?

      By MBS206 · Posted

      -10 is plenty for running to an oil cooler. When you look at oil feeds, like power steering feeds, they're much smaller, and then just a larger hose size to move volume in less pressure. No need for -12. Even on the race cars, like Duncans, and endurance cars, most of them are all running -10 and everything works perfectly fine, temps are under control, and there's no restrictions.
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      Update: O2 sensor in my downpipe turned out to be faulty when I plugged in to the Haltech software. Was getting a "open circuit" warning. Tons of carbon buildup on it, probably from when I was running rich for a while before getting it corrected. Replaced with new unit and test drove again. The shuffle still happens, albeit far less now. I am not able to replicate it as reliably and it no longer happens at the same RPM levels as before. The only time I was able to hear it was in 5th going uphill and another time in 5th where there was no noticeable incline but applying more throttle first sped it up and then cleared it. Then once in 4th when I slightly lifted the throttle going over a bump but cleared right after. My understanding is that with the O2 sensor out, the ECU relies entirely on the MAP tune and isn't able to make its small adjustments based on the sensors reading. All in all, a big improvement, though not the silver bullet. Will try validating the actuators are set up correctly, and potentially setting up shop time to tune the boost controller on closed loop rather than the open loop it is set to now. Think if it's set up on closed loop to take the O2 reading, that should deal with these last bits. Will try to update again as I go. 
×
×
  • Create New...