Jump to content
SAU Community

Recommended Posts

Just a quote from www.popularmechanics.com , just incase you don't believe me.

(Battery) Charge

With the battery charged, open circuit voltage should be 12.6 to 12.8 volts with the engine off and all loads off. With the car running and all loads off, the voltage should be between 13.6 and 14.5 volts.

The only other thing is where you tested the voltage. Could be the terminal clamps are loose or the leads are not conducting enough current.

If it is the starter motor, try giving it a tap with a hammer or metal pole, but it sounds to me that it is trying to turn over.

Link to comment
https://www.sau.com.au/forums/topic/168052-car-wont-crank/#findComment-3109387
Share on other sites

Yah! I think its the battery too. It happened last year during the winter the same thing. I did not take note of it as I thought its OK. But now, i think i have to replace the battery. Anyone know where to get one? I have read somewhere that the battery must be a "dry" type as it is place in the rear boot. Hmmmm.......must be expensive!!!!

Link to comment
https://www.sau.com.au/forums/topic/168052-car-wont-crank/#findComment-3109486
Share on other sites

theres a place in queanbeyan which sells batteries wholesale, good price and the guy knows batteries, he spent about 10 minutes explaining why i needed a certain battery for my car :domokun:. Just tell him the make and model and he will go hunting through his warehouse. Can't think of the name but its on Uriara Rd near the roundabout just after the petrol station.

Link to comment
https://www.sau.com.au/forums/topic/168052-car-wont-crank/#findComment-3109534
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...