Jump to content
SAU Community

Recommended Posts

my car battery is completely dead , i have d/c the positive lead from it because my alarm wont stop sirening . this is probably the back up battery for the alarm . and everytime i connect it , it keeps making the siren .... hence the car is dead .

what am i to do next ? im stumped . im considering calling the NRMA , but if i cant do anything what could they really do?

any answers would be great ?

Link to comment
https://www.sau.com.au/forums/topic/168362-car-battery-dead/
Share on other sites

buy a new battery or charge the one you have now.

there a three reasons a battery goes flat, alternator not charging properly, a current draw or a dud battery.

if ur a NRMA member then give them a call as they can help u

my old man said if you get it started, drive it around for an hour and then can't start again then the alternator is f**ked.....otherwise something must be draining it

It could also be that the battery is cactus. Thats what happened to me, it would ONLY JUST start after an hour driving around. Then got a new battery about 2 weeks ago. No issues since then.

:stupid:

this all happened because i had the stereo left on for a few hrs .... jumped it twice since then , but havent fulley charged it cause i cant drive for another 4 weeks .. so its gone flat again , because one nigth i went out and was working on my car and had headlights on ... drained again ... although , the other day i walked by my car and checked the door if it was locked , and the alarm sounded cause it was armed and opened ..... the remote wouldnt shut it off , cause no power - so i dcd the battery ..

i doubt the battery is gone , i think its just completely dead ..... and to the point where it wont charge through a jump .

how much is a new battery? if i called NRMA they could bring one , so iv heard...

between $30 for a super cheapy to $120 for a decent one.

(the more you pay the more plates per cell you get in your battery)

i suggest if you have a problem of draining your battery you should invest in a battery charger.

to check the charge rate, start the vehicle grab a multimeter and set it onto voltage.

turn off all your lights and air con and place the multi meter on the battery if its reading a constant high 13V or low 14V thats good, now put some load on the battery by turning on your stereo or lights and do the same as above it should now read a constant low to medium 13V.

thats the most accurate way of checking if your alternator is working.

to check for a current draw have everything turned off inc your ignition. disconnect the negative battery terminal. now set your multimeter to amps and place one multimeter cable on the battery post and one on the terminal. your multimeter should be reading 0.10 -0.01amps if its around 0.2 or higher then there is a current draw.

to find out where the current draw is coming from keep the multimeter as above and start removing and re-fitting your fuses one by one until the draw goes away.

this just narrows down all the possibilities of what could be drawing current.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...