Jump to content
SAU Community

Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

Or people could just get their own manifold converted, or SAU could have a donation plenum, which would get converted to front facing, then their own plenum would become the donated one. BTW the rb20det is not the same as rb25det. By the way, if your looking for something sexy thatll look good at car shows etc, the converted plenum probably isnt for you, there are greddy ones that probably are.

Yar, but you would be wanting some coin in exchange right? thats usually when the word Keen is used.

SST Steve, how much are these plenums retailing for? Do they just fit on factory runners? Do they have trumpets or utilise angles ? If there is one for the rb20 ill be interested in the future.

Cheers

LOL

anyways fellas I have Pmed both gradenko and R33 impul so all is good. Gradenko lets hope the budget holds out, no cyclones on the horizon up in the northen suburbs

thanks for all the input

i think that it seems like such a simple idea and such an easy install in terms of simplicity, it is difficult to reach but not alot can really go wrong from looking at it hey.

Anyways this can be closed if needed,

hey steve whazz the cost the for the per4manz ones

with the amount of engineering GReddy and other intake plenum designers put into their plenums one would have to assume that simply relocating the throttle body isnt going to work quite as well. but on a budget there isnt anything else

youve also got to ask yourself what saving 1-1.5m of piping is really worth with reference to a cut n shut job

youve also got to ask yourself what saving 1-1.5m of piping is really worth with reference to a cut n shut job

IMHO, yes, its definetly worth removing 1m or so of piping, even if its means using a cut'n'shut. In any case, I'll post a objective review after its done. Specifically looking at power gain after tuning (if any) and change in throttle response. Could also put it on a flowbench to check flow distribution. Anyone know of a place that'll do it at mates rates?

Take a look at 1JZ and 2JZ plenums. From the outside they look remarkably similar to our cut'n'shut job.

its the length of the runner relative to the original position comapared to the relocated position thats important though

ie nissan designed cylinder 1 and 6 (the ones people question) to be the same distance from throttle body, cut n shut the plenum and now its completely different

I'm not convinced Nissan went to any great lengths designing that plenum. Sure, it worked out well that air flow distribution was equal, but it seems to me their number one design goal was shortening the distance from ic to tb. The inside of the stock plenum doesn't have any special deflectors or flow distributors (AFAIK), and like I mentioned, there doesn't seem to be anything stopping it from behaving like a JZ plenum.

Just in case, I'll clean and flow the injectors, installing the highest flow for cylinder 6 (cause its most likely to run lean) and lowest flow for cylinder 1.

Originally posted by Steve-SST

Per4manz now have new custom plenums for RB25s.

Heya Steve how much are they charging for these off the top of your head? do you think they would do an sau discount or something if a few were interested?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...