Jump to content
SAU Community

Recommended Posts

hey guys i have an 97 stagea and im wonderig what the norm is for idleing on the highway? at around 100 to 110ks mine sits on 3 grand.... just seems to high.... feels like the auto needs to drop back.

have had it to the auto shop and hooked it up to the scanners. everythings doing what it is supposed to. was told that it could be the tps switch that might need adjusting. adjusted it in increments to no success. weird thing is it has an open centre in it?? thought it would run an lsd???

any other ideas.???

also the 4wd doesent work. havent even looked into this problem yet. where do i start????

Link to comment
https://www.sau.com.au/forums/topic/168724-idle-at-100k/
Share on other sites

do a search in the general automotive section, I remember seeing a DIY in there about reseting idle and it had something to do with an air bleed on the plennum.

Mine (was) at 2500 - 2600 at 100kph and I have 17" on 45 series and a stock as a rock auto.

Link to comment
https://www.sau.com.au/forums/topic/168724-idle-at-100k/#findComment-3117996
Share on other sites

thats a real worry - has the attessa pump got any fluid in it?

It may just need bleeding, but I would have a close look at it if I were you. Running the pump and/or transfer case dry (if that is the problem) can get very expensive. Usually, the only way to get a stagea to run in RWD only is to drop the front driveshaft out - the old "just pull the 4WD fuse" doesn't really work and can actually cause damage if left like that.

Link to comment
https://www.sau.com.au/forums/topic/168724-idle-at-100k/#findComment-3118075
Share on other sites

Mines auto and sits just on 2500. Worked out it does just on 40k/1000 when the converter is locked up. Am running 17"

225/50/17 Federal595'

Just a further on this.

I got wacked twice for "exceeding the speed limit" but concluded the checking methods were suss. No charges.

I run a general rule, 10, 20, 30, 40 kph/1000rpm in 1st, 2nd 3rd OD. Around the Mountain (town) I now popthe OD to OFF.

Keep to 2000 and no dramas. Thats what I do.

It is interesting to see that there is quite a difference between various owners. you would have to check on the final drive ratio

and the actual diameter of your wheels to see exactly where each vehiclewas at. And if auto that the converter actually does lock up.

My old RMR30 (used to) did 50k/1000, locked up. Couldn't get her started for her final triptoday. I think she knew.

She used to peak about 4250. But the RMR30 were a very slippery vehicle and had one of the lowest coefficients of drag

factors of most cars of its time. It is what made them fast, not quick, fast.

So there are a lot of factors that govern the revs/km. All aspects have to be taken into consideration.

Owning a NIssan is such fun. I have five. Well four after today.

Link to comment
https://www.sau.com.au/forums/topic/168724-idle-at-100k/#findComment-3119526
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...