Jump to content
SAU Community

Malaysia.....where To Find Bits

NO_RSPECT

By NO_RSPECT,
in Western Australia

 Share

Recommended Posts

Yawn Mentor

Yawn

Posted
Posted
i am inKuala Lumpur at the moment..

anyone from here or along those lines.. know if there is anywhere to buy bits...

tail lights.. kit bits... dash kits.. any sort of rice at all..

holla back i am here till the weekend..

Yeap go to Sunway. There are at least 20 car related shops there. Also if you have the time you can head over to SS Racing nearby this place called OUG. If you were to go to Sunway, ask anyone there and they'd be able to direct you to SS Racing which isnt far from Sunway. They have a very large selection of parts both 2nd hand and brand new.

Yawn Mentor

Yawn

Posted
Posted
when I was there, I went to a place called Brothers car parts and accessories.

they had a huge selection of car parts and audio gear. Heaps of rice parts as well.

Haha Brothers is sort of like Autobarn here. They have a lot of cheap rice parts but they are pretty poor quality and i doubt they cater to skylines besides some universal stuff. I personally wouldnt recommend going there coz you may be quite disappointed haha. They're ok for audio gear though.

gun-r32 Collaborator

gun-r32

Posted
Posted

Sunway ftw. Beware though, car modification in Malaysia is expensive, therefore don’t expect to get quality bits cheap (as I found out), you will be disappointed. Nengun / Greenline is way cheaper. Went to Brothers also, looks good from the front…lol, inside lots of crap everywhere, mainly just tacky stuff to bolt onto your Proton (of which there are eleventy billion of in KL).

vbevan Apprentice

vbevan

Posted
Posted
Sunway ftw. Beware though, car modification in Malaysia is expensive, therefore don’t expect to get quality bits cheap (as I found out), you will be disappointed. Nengun / Greenline is way cheaper. Went to Brothers also, looks good from the front…lol, inside lots of crap everywhere, mainly just tacky stuff to bolt onto your Proton (of which there are eleventy billion of in KL).

I'd say you're back but don't waste your time at Brothers. i went there last time I was in KL and it's exactly like supercheap, but much much worse. There' not one real performance part in the shop, all "Monza" and "Type S" brand type stuff. Audio might be ok there though. There really isn't much quality car parts to legitimately get in M'sia unless you know people :)

KeeFy Mentor

KeeFy

Posted
Posted

It really depends, where you look. There are places in malaysia that does some serious mods and stuff. You just need to look around. Pick up their local car mags that are in english, and you'll get quite a good idea, loads of adverts, some with prices to boot. So you can roughly gauge how much after exchange rate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...