Jump to content
SAU Community

Recommended Posts

Hey guys, i got a 96 skyline bought it bout two months ago completely stock

I put a 3" turbo back exhaust, turbosmart manual boost controller, K'n'N panelfilter and fmic and running boost at 10-11 psi. I'm now getting a ticking noise sounds like its coming from the injectors, are my injectors no good or is it something else.

if injectors should i just replace them wit stock new ones or put aftermarket ones in.

Link to comment
https://www.sau.com.au/forums/topic/168783-ticking-injectors/
Share on other sites

try havin them cleaned or u sure its not ur fan hittin ut cooler pipe.

na its not the fan i trimmed the fan when i installed fmic and lubed the belts only last week its def coming from inside its a little worse under acceleration. i didnt wanna mechcanic feeding me shit...

Injectors are supposed to "tick". If it has only just started, it could be a stuck lifter - Nulon make stuff supposed to clear them. Or it could be "piston slap", where the piston and bore are becoming mis-matched for roundness.

Injectors are supposed to "tick". If it has only just started, it could be a stuck lifter - Nulon make stuff supposed to clear them. Or it could be "piston slap", where the piston and bore are becoming mis-matched for roundness.

thanks for the help guys only new to all this but learning heaps yeah i bought some stuff from nulon today injector cleaner i'll see how it goes hope it works keep you posted

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...