Jump to content
SAU Community

Recommended Posts

Hey Guys,

i've just completed a few mods to what was previously my stock R25DET R33

Here's a list of mods:

3inch Exhaust, front pipe back, including high flow cat

HKS pod

Greddy FMIC

HKS Electronic Boost Controller

Now there have been a couple of issues that have come up as a result.

The car was previously runinng perfectly, but now that i have installed these mods, it seems to be hunting a fair bit on start.

After driving it for a few minutes, it usually works fine.

The other things that scared the crap out of me the other night is when i had boost up around 14psi and the turbo just suddenly cut out around 4,500-5,000rpm

What can i do to resolve these issues??

Thanks guys

Edited by Tommmo
Link to comment
https://www.sau.com.au/forums/topic/169504-r33-gts-t-got-a-couple-of-issues/
Share on other sites

Check all your vacuum lines to start off with that can cause some problems. As for the turbo cutting out it could be fuel cut. Dont know too much about nissans but i know with some turbo subarus once it his boost cut it will bring a limiter it. Do you have anything like a fuel cut defender?

It would probablly be with runnnig a fault check on your ecu to see what fault codes it throws up.

Hey I reckon you check your TPS (throttle position switch) this can be affected. 14 psi is too much on a stock turbo turn the boost down to 10psi to be safe. Your pod filter would probs be causing probs too cause its sucking in hot air. Id suggest get some kind of aftermarket ecu or atleast fuel controller piggyback. If you search you'd see this is covered tonnes of times. good luck mate hope it all works out hate hearing of a unhealthy R33. also go to a mechanic and get a consult plugged into your car and when your car starts to hunt they'll tell ya exactly whats up.

Edited by LatinR33
Hey I reckon you check your TPS (throttle position switch) this can be affected. 14 psi is too much on a stock turbo turn the boost down to 10psi to be safe.

I run it at 10psi all the time, i only have it at 14psi occasionally as i've heard they can handle this much. (i hope)

Engine wasn't designed (or programmed) to ingest air at 14psi. Hold it back (maybe 12psi), and it should be ok.

If you are running stock ECU, try a reset to have the ECU re-learn the startup.

Check all hoses as could be a leak somewhere since the tubing might be old and flakey..

You can try cleaning you AAC and resetting the idle -> http://www.skylinesaustralia.com/forums/in...howtopic=110431

Also sounds like R&R'ing at high rpm/ high boost. Since night = more oxygen in air and car R&R'ing (Rich and Retarding)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...