Jump to content
SAU Community

Recommended Posts

Ok first the car is a S2 R33 GTST with front mount, 3" catback & pod. In the last couple of weeks, there have been a couple of cases where I accellerate hard and around 4-5k rpm the engine has hit a limiter.

The limiter feels like a fuel cut, if you have ever been to the speed limiter in 5th gear (~5500rpm) its a bit like that. Happened this morning in 2nd around 4-5k rpm...

Anyone know what would cause this? I'm pretty darn sure it wasnt the 7k limiter.. its a bit faster then that.

Cheers,

Ryan.

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/
Share on other sites

Just stock boost. It only lasted 1 second at the most... definately not the rev limiter.

I've hit speed limiter (fuel cut pretty much right?) in the non turbo and its similar to that, much quieter then a rev limiter. Like a low fast rumble..

Edited by SKY RYAN
Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3135940
Share on other sites

Yeah just drove home and went to overtake someone in 2nd and it did it.. then on the freeway i droped down to 4th, then to 3rd and gave it stick and yeah it did it again...

So coilpacks eh, is it bad to drive like it is now? or can i just drive it soft..

EDIT: Wer can i get me sum coilpakz!!1!1

Edited by SKY RYAN
Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3136084
Share on other sites

Talk to paul and Alistair. See what they say. I dont think it will be warranty though.

If you do want to get them from Slide, let me know as i need to order a set for for an SR aswell. We can do 1 order and try to save a bit of freight :)

Cheers

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3137401
Share on other sites

I'd be checking all your silicon joiners.. I had a hose clamp pop off (just the clamp not the silicon) and when it got to about 4k it felt like it hit a wall.. took me a bit to figure out as it wasn't like when the hose popped right off (when it popped right off it wouldn't idle and pumped HEAPS of black smoke).

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3137711
Share on other sites

the split fire coilpacks are easy as to replace, yeh you have to take off that black cover, its about 8 screws that require an allen key,

under that is the coilpacks, just have to unclip the wiring loom they are connected to and then each coilpack has 2 screw holding them down,

just take the old ones out and pope the new splitfires in, easy :P

Link to comment
https://www.sau.com.au/forums/topic/169692-problem/#findComment-3137807
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They care about emissions, and cost the most. Save weight where possible, and make manufacturing easier. Less material also let's the engine transfer heat to water quicker, and bring the engine up to temp quicker, better for emissions and getting them past their warranty period.
    • I was under the impression the reason why OEMs are going with solutions like relatively thin "right-sized" cylinder walls with technologies like PTWA and open deck is because they care a lot about whatever marginal knock margin benefits they get from that vs the structural rigidity benefits of a closed deck block and thicker cylinder walls. I also see some weird stuff like plastic inserts in the water jacket around the cylinders to try and equalize cylinder wall temperatures. re: the PRP blocks and heads at the end of the day it's hard to know what is and isn't going to work there, just have to see what the initial buyers say about it.
    • Which is why I didn't mention that hardness testing, and specifically mentioned the bore and deck thickness testing. Yeah, not really. The bore temperature will be a lot more even around the top half inch or so, where the material distribution is dominated by the deck, and which is the only place where the bore surface temperature heating any gas in the cylinder is likely to have any effect on detonation. Think about it. Another inch or so down the bore, you might have a hotter spot. The gas there might get a bit hotter, then the piston rises squeezes that gas away from there at high speed and mixes it with other gas from nearby. Instant dilution of the problem. I'd be surprised if it was an issue at any time other than in racing engines or OEM dev engines being run at the ragged edge of tuning. Say what now?
    • https://dsportmag.com/the-tech/education/engine-tech-material-hardness-testing/ The PRP testing on block hardness I'm not sure how much it actually can be trusted. The thinner cylinder walls on RBs is a bit of a problem vs 2JZ but it really depends on the design goal. Siamesed cylinder bores like a 2JZ cause uneven cylinder wall temps too, which means a bit of distortion induced by that + the hotspot can affect knock margin. Something that actually gives me a bit of pause with the PRP block, whether super thick cylinder walls are going to keep it from being drop-in compatible on an otherwise OEM rebuild. 
    • Yeah very valid point. I am waiting for one of the other tuners to come back from vacation so he can help me a bit when the cat is installed again. In the meantime I am going to finish up my polishing and ceramic coating that I have started myself.    N45 Dr Beasley product is highly recommended for a paint primer / polisher. Using this EXO Gtechniq also for the ceramic but next time might use the light serum before hand also. Looks great. 
×
×
  • Create New...