Jump to content
SAU Community

Recommended Posts

Hi guys,

Pretty much im running these mods on my r32 gtst:

high flowed turbo

full hks xuast

pod

and boosts up to around 11psi.

just feel like its down on power and could have more potential.

Not looking at spending too much for a tune, but something decent.

Anywhere around south east qld / gold coast would be great.

Cheers

Tone

it is worth remapping the standard ECU if your not going to do any more mods... so i'd suggest getting a front mount before you got it remapped, cause otherwise later down the track u'll need to remap it again.

a SAFC is a piggy back computer that modifies the reported voltage from the air flow meter. its good for some tweaking, but if you want to take full advantage of that high flow, either an aftermarket ecu or a remap is in order.

yeah would have the standard ECU.

Is it not worth while remapping the standard computer or ?

whats safc?

in that case, Mercury Motorsport and DrDrift are the only 2 i know of who have the facilities to remap the stock ecu.

yes, if you increase the boost it changes the tune. do you have a boost controller at the moment ? if not, i would get an EBC and give mercury a call. they'll set whatever boost you want and remap to suit. Also, if your gonna be putting out more power, make sure your fuel pump is up to scratch.

fyi i think a remap comes in at about $500

as the others have said the safc is a piggy back computer, it wont give you the same tune a a remap, however i dont think the total would cost as much, in saying that if you have the $$$ get the ecu re-mapped it is worth the extra dollars in the end

stuff it if ur gonna run 12psi on the standard sucker ull be fine with the nissan ECU relearning itself and save ur money and buy a full ecu eg pfc.

but if ur doin massive increases eg new turbo injects afm NOS (lol) then u should check afr and tune accordingly.

go see the guys at 101 motor cafe. From my experience there are alot of bad tuners out there and i wouldnt recommend anywhere else

Edited by r_speedfreak_r

just trying to get an idea of things,

hopefully will be slotting in a new turbo/z32/injectors/pump in the next few weeks what would you expect to pay for someone decent to tune the car, it already got the usuals and powerfc

i know matt spry is awesome from the word of mouth but seemed quite expensive ($500 to do a tidy up tune on the car as it is[tuned by APC previously])

or is that the sort of price all tuners charge

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...