Jump to content
SAU Community

Recommended Posts

G'day people,

I'm having a problem with my hicas. I've tried searching for it in other threads but nothing to really match.

Well, my hicas pump sometimes plays up when i take the key from the ignition and have the car running on the turbo timer. a loud pumping/knocking noise comes from the hicas pump and on closer inspection you can see the pump convulse every time it 'pumps'. Also, when the timer is running and the fuel pump primes, it starts to 'pump' and make noises then stops when the fuel pump has finished priming. it does not do this all the time though. I've also noticed that if i have my headlights on and then take the key out of the ignition with the turbo timer on, the problem will occur until i turn the headlights off, but even this sometimes doesnt work and it will keep pumping and make the knocking noise. and lastly, it will also occur when i press my foot on the brake pedal with the turbo timer on. Sounds like an electrical problem but not sure.

I hope this helps

Link to comment
https://www.sau.com.au/forums/topic/170383-hicas-is-playing-up-r32-gtr/
Share on other sites

How old is the battery?

good question. i'm guessing its old. i've had the car for around a year and 4 months. i have never changed the battery, though it has been push started once :P and i have to start my car at least once every third day or the cranking sounds really slow and tired.

if it helps, when i took my aircon condenser out i undone the rubber hoses that go to the power steering cooling tube (thin pipe with heat sink fins at front) and in the morning when i woke up there was fluid on the ground. i had to top up the reservoir.

yeah, i'll get a new battery. you mentioned the speedo cable. i seem to have the speedo 'boogie', the needle jumping around under 20 km/h and

at high speeds the needle pausing then going again. bugger

yeh mines does the EXACT same thing....!!! well all before i put the new one in, although it still didnt fix the pausing at high speeds. It must be the cluster, or maybe something on the transmission side of the cable, NFI! When you figure it out let me know!

  • 10 years later...

talk about bringing up an old thread... after believing i had a fuel pump issue because of this "pump" and "knock" on ignition/prime, i changed the fuel pump... problem still existed, decided to have a look under the back of the car and feel around to realise its the hicas motor. I took the plug out the hicas motor and "pump" and "knock" disappeared. Did anyone of any luck with sorting this out? was it a battery or something else... all signs are pointing to faulty hicas motor as car has developed a shake at higher speeds which i couldn't locate previously but don't want to replace motor for no reason if there is another simple fix

 

thanks,

 

Mark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...