Jump to content
SAU Community

R32 Gtr Front Bar On A Gtst

S13/r32 maniac
 Share

Recommended Posts

S13/r32 maniac Enthusiast

S13/r32 maniac

Posted
Posted

Hey, i want to put a gtr front bar on my gtst (r32). I have looked into prices of some gtr copy front bars for gtst. i went to carmate.com and they sell one for $350 and i went to justjap.com and nismo.com and they are both around the $500-$550 mark. What do you guys recommend where to buy one from that is quality and will fit nicely. Please share your experiences/knowledge on this subject. Thanks

Link to comment
https://www.sau.com.au/forums/topic/170672-r32-gtr-front-bar-on-a-gtst/
Share on other sites
MR DMD Contributor

MR DMD

Posted
Posted
Hey, i want to put a gtr front bar on my gtst (r32). I have looked into prices of some gtr copy front bars for gtst. i went to carmate.com and they sell one for $350 and i went to justjap.com and nismo.com and they are both around the $500-$550 mark. What do you guys recommend where to buy one from that is quality and will fit nicely. Please share your experiences/knowledge on this subject. Thanks

Hi, got one for you for $380 plus delivery and guarantee fitting is perfect.

Blitz Grand Master

Blitz

Posted
Posted
Hey, i want to put a gtr front bar on my gtst (r32). I have looked into prices of some gtr copy front bars for gtst. i went to carmate.com and they sell one for $350 and i went to justjap.com and nismo.com and they are both around the $500-$550 mark. What do you guys recommend where to buy one from that is quality and will fit nicely. Please share your experiences/knowledge on this subject. Thanks

You get what you pay for.

I have a GTR bar from Just Jap on my R32 GTS-T and my painter commented that it was one of the best fibreglass bars he has ever seen.

Its also by far the best made and most solid fibre bar and I have come across.

salad Veteran

salad

Posted
Posted (edited)

I got genuine on mine too and the fit isn't too bad, not perfect but will take small taps and bumps better than fibreglass. Do have to use the GTR reo though.

I paid $300 for mine with a set of 4dr sideskirts, but that was an absolute bargain.

Before that I did have a cheaper fibreglass copy though, but wasn't happy with it.

Edited by salad

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...