Jump to content
SAU Community

Recommended Posts

Hig guys,

not long ago i posted a thread asking the price of r32s. Ive decided to spend that little bit extra and get an r33 gtst cause the dont seem to be that much more expensive.

I was thinking about $15000. Does this seem about right for a nice and clean r33 gtst with excellent paint, bodywork and mechanicals.

I live in sa

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/170751-buying-r33/
Share on other sites

I agree - I was buying a car for wife the other day and just for interest searched R33 skylines (i've owned mine for 5 years now) I could not believe there were R33s on carsales.com and the like for 8 grand!

Remember this tho - even if you get a R33 GTSt for around $10 grand - you will be spending another ten grand on wheels/tyres/more boost/body kit etc etc etc ..... the amount of aftermarket stuff you will buy will add up

Link to comment
https://www.sau.com.au/forums/topic/170751-buying-r33/#findComment-3151676
Share on other sites

$15000 should get you something pretty decent down hear in S.A but you should try and budget in money for insurance cuz these cars get stolen a fair bit. I bought mine fairly standard neally 2 years ago and the amount of money you spend doin it up adds up quickly if i could go back id prolly buy one already done up.

Link to comment
https://www.sau.com.au/forums/topic/170751-buying-r33/#findComment-3151796
Share on other sites

$15,000 will buy you one fairly decent with a few niggles. $17,000 should buy you one with no hassles. Look for if it has had the belts changed, regular services/oil changes, good gearbox, no rattles etc etc. Basically look at all the internals first and foremost. Your priority should be the overall condition of the car. Not exhaust, rims etc. If I could go back I would buy one that had already been owned and driven by someone who did all the regular maintenance. It's so much less of a hassle. When I bought mine (which I am the first owner in Aus) I had a full tune, timing belt changed, new Iridium spark plugs installed, compression test, all fluids replaced with high quality products, an alarm that complies with insurance (most alarms don't which void your warranty if broken into). I spent around $2,000 on all this including labour. Then I had insurance! But my R33 runs like a dream and I treat it well. I see a lot of shitty R33's going around that look neglected and don't sound so good. So it's best to search around until the right one comes up.

Link to comment
https://www.sau.com.au/forums/topic/170751-buying-r33/#findComment-3151965
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, the trouble with that ^^ is: The configuration shown is absolutely a 1-way, not a 1.5-way. There is no way that a 1.5-way can be said to offer LSD action only on acceleration. If Nismo cannot get that right, then it is impossible to believe their documentation. That ^ is not a 1.5 way setup. That is a 1-way.   And so now I have allowed all doubts to flourish and have gone back to look at the MotoIQ video. I originally made the mistake of believing him when he said "this is a 1.5-way" at the ~6:10 mark. Because what he did was take the gear assembly out of the 2-way opening and just rotate it one place to the left to drop it into the 1-way opening. When he dropped it in there, the cam was "backwards" compared to the correct orientation shown in all other photos of that config. The flat shold have been facing the 1° ramp side of the opening, not the 55° ramp side. And I thought, "gee that's cute", but I was concerned at the time, when he put the other ring back on, that the gap between the rings looked like it was wider then in the 2-way config. And then I said a lot of things in my long post on Tuesday that could only make sense if the guy from MotoIQ was correct about what he'd done. BUT... I have now done my homework. I grabbed a frame of the video with the 2-way config, and then grabbed another with the "1.5-way" config, snipped out the cam and opening of that frame and just pasted it direct on top of the 2-way config. I scaled it so that the triangular opening was almost exactly the same height in both. AND.... the gap between the plates is wider with the cam installed in the triangualr opening backwards. That is.... it cannot go together that way. There would be massive force on the plates all the time, if you could even reassemble it.  So, My statement on the matter? The Nismo diff is actually only a 2-way and 1-way. There is no 1.5-way option in it, regardless of what they say. Here's a photo of a real 1.5-way ramp opening from Cusco (along with the 1 way option). And the full set of 1 through 2 way options from their racing diff, which is not same-same as what we'd typically be using, but...the cams work the same. A little blurry, but it comes from this Cusco doc, which is quite helpful. AND.... Cusco do in fact do what I suggested would be sensible, which is to have rings that do 1 and 1.5, and 1.5 and 2. Separately.  
    • Welcome Adam. Car looks great!
    • "With a 1.5-WAY, the LSD is effective only during acceleration."
    • Well it wasn't as easy as I thought.... and it also wasn't in my original manual which I did end up finding. They discuss the process in the Nismo catalogue though and it requires slight machining. Page 145.  NISMO PARTS CATALOGUE 2020
    • I'm an idiot, my intercooler is rated for 1000hp. I had clicked on the wrong product. Knowing the delta P would be nice, but I'm doubtful I'll do it. Now as for an EMAP, that would be great and I'll get around to it eventually but from my findings in my last post, I'm considering a turbo swap now. 
×
×
  • Create New...