Jump to content
SAU Community

Recommended Posts

Hey guys ive notice a strong fuel smell in my car everytime i hit the throttle? ive did some checks like checking the engine for any smell or leaks but douldnt see any, so i go to look under the car for leaks on exaust etc... still no sign, so checking to see if they are coming from the air vents while window is up still no sign, but once i drive my car with windows down, the strong smell just appears?

any ideas?

cheers

Link to comment
https://www.sau.com.au/forums/topic/170954-strong-fuel-smell/
Share on other sites

Hey guys ive notice a strong fuel smell in my car everytime i hit the throttle? ive did some checks like checking the engine for any smell or leaks but douldnt see any, so i go to look under the car for leaks on exaust etc... still no sign, so checking to see if they are coming from the air vents while window is up still no sign, but once i drive my car with windows down, the strong smell just appears?

any ideas?

cheers

Hows your fuel economy?

I sold my old R33 a while back and it had a similar problem, (could always smell fuel but could never find any leak) the guy who bought it off me said when he got it tuned the oxygen sensor on the exhaust was faulty and it was causing it to run too rich using too much fuel. If you have no fuel leaks and it's not been replaced in the last 40K thenit may pay you to replace it.

  • 2 weeks later...
Hows your fuel economy?

I sold my old R33 a while back and it had a similar problem, (could always smell fuel but could never find any leak) the guy who bought it off me said when he got it tuned the oxygen sensor on the exhaust was faulty and it was causing it to run too rich using too much fuel. If you have no fuel leaks and it's not been replaced in the last 40K thenit may pay you to replace it.

had the elecrican down the block from me have it checked on the diagnostic but hey didnt notice any faults or what so ever on the o2 sensor? also i had my ecu reset before i got it on the diagnostic??

Check fuel filler, fuel tank breather lines, etc for perished hoses.

mechanics have tried looking for leaks through the fuel lines etc... but had no clue?

*note* ive got a dump pipe straight of my wastegate welded onto the manifold? could the smell come from the dumpy?

Fuel filler, from what i've read here. A mate of mine had the same thing (very strong smell when cornering) and it ended up being a crack in the rubber surround of the filler... which is added when complianced. (at least on his car it was)

i have the same prob with mine, i noticed a while ago wen i turn the car off i could hear a hissing sound from the fuel cap and the smell seems to be coming from there, going to put a new cap on it now to see if maybe thats the problem, u no, the cap not shutting properly, mite resolve my other acc issues, maybe im losing fuel pressure.just a thot, check it when u turn ur car off, listen to the fuel cap and smell that area.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...