Jump to content
SAU Community

R32 GTR - not driving straight

doug3rd
 Share

Recommended Posts

doug3rd Apprentice

doug3rd

Posted
Posted

I in the market for a R32 GTR, and was almost ready to buy one car until I test drove it. The ride was smooth and the engine great, but the car pulled slightly to the left.

I figured that this might just be wheel alignment, but when I braked, the car really pulled to the left.

Is this a bad car, or is it just a case of bad wheel alignment and/or bad brake pad?

As far as I can tell, the car hasn't been badly smashed. Is there anything else I can check?

Link to comment
https://www.sau.com.au/forums/topic/17102-r32-gtr-not-driving-straight/
Share on other sites
AtomicBomberMan Experienced

AtomicBomberMan

Posted
Posted

hmmm... sounds like the bush in the contol arms are deteriorated causing excessive movement. apparently they can only bought as a whole arm and not just the bushes. they are about 250-270 each from nissan and about 200 bucks labour to do the two. found out the same thing about my car today!

doug3rd Apprentice

doug3rd

Posted
  • Author
Posted

The car is $26k, insurance #3k... Overall, the car is quite cheap for what I'm getting, unless this problem turns out to be serious...

AtomicBomberMan, did you car feel tight or loose in the front? Because this car feels tight, which scares me into thinking it may not be the bushes... I will get it checked out though... If it costs me only $700 to fix, then it's still a good buy..

Mick Trainer Rising Star

Mick Trainer

Posted
Posted

Doug,

Where is this car? What color is it? I not long ago bought a 32 gtr and drove heaps of them. If you tell me these details I may be able to give you insight into it a bit if I know the particular car. Many of the ones I looked at are still for sale.

Mick

AtomicBomberMan Experienced

AtomicBomberMan

Posted
Posted

its really difficult to say, i really think you need to get under the car to see. i noticed that my gtr will pull quite aggressively if the road is uneven to the left or right. this might have something to do with the 17" wheels though. the cars underbody tells a lot of stories.

doug3rd Apprentice

doug3rd

Posted
  • Author
Posted

Mick, It is in Sydney, Burgandy colour, 1994. I went up to basically buy the car, but this scared me off a bit...

Do you still know of any orignal r32 GTRs around? I can only find one in budget, but he wants $27k, and it is a 89, so the 15 rule will probably drop its value at the end of the year. It makes it a difficult time to buy.

AtomicBomberMan, thanks for that tip, I'm going to get the car checked out by NRMA, so I'll ask to look especially at the bushes in the control arms...

One question though... have you tried rocking the front tyres? This car did not have any end-play that I could find. I'm not a mechanic, but I assume that if the front tyres feel tight then it's not the bushes... Do you have any end-play in your front tryes?

Mick Trainer Rising Star

Mick Trainer

Posted
Posted

How much are you willing to spend Doug so I know what you are looking at. There are a few around. There was a ripper Gun Metal Grey one I looked at that I think is still for sale but I dont know about $27k but it would not be far off. There was a black one also I think is still there. It was a little untidy but mechanically very good. I think it is still around also.

Mick.

doug3rd Apprentice

doug3rd

Posted
  • Author
Posted

Yeah Mick, I think I know the two you mean... The black one is in Templestowe and the other in Keilor...?

I like the gun metal one, but I am worried that I will loose too much money on it because it is 89....

I haven't driven either one... The black one was quite good, but it did have a strange back-off noise when you rev the engine... I know rb26s are strong, but it sounded a little mettallic...

Have you driven either?

I am willing to spend up to about $30 (inc on-roads), but really not beyond that... and I really want original or close too... That is why I liked the grey one........ but for the same money I could get the black one, which is 4 years younger. Such difficult decisions.....

Mick Trainer Rising Star

Mick Trainer

Posted
Posted

The grey one that I saw was a 93 by memory but it was Keilor was. Guy named Alex owned. If it is the same car is is really nice and straigt. Original except for an exhaust and air pods.

I have driven them both. Black one drove nice, had good power but had had a lot of mods on it including boost controller which is a concern. It had had a bit of body work done on it as well. But overall come up alright. All tests mechanincally came back good but it definalty needs some body work too tidy it up.

The grey was was very nice mechanically and drove really well. Very tight. I put an offer in on it that was rejected but it is more than he is asking now if this is the one.

I would say though that with a 89 I would wait and buy one from Japan once in the new year. The price will definatly drop and you should be able to get a nice one if you take your time. You have to be careful no matter what you do and it is always a risk but the price for an 89 may be so good then that it is worth taking the chance.

Mick.

doug3rd Apprentice

doug3rd

Posted
  • Author
Posted

Must be different keilor/grey cars, because this was advertised as 90, but was an 89... guys name was Darren, and it had a std exhaust and filter...

hmm.. interesting...The black one I saw has supposedly had a 'turbo timer' removed, but there was no mention of a boost controller... I didn't look at the black one too carefully because it had the pods and exaust, and was lowered...

Sounds like you've been doing you homework also.. Can I ask what car you eventually bought and for how much?

Cubes Grand Master

Cubes

Posted
Posted

Always get a car checked over quickly by your local mechanic on a hoist before you buy it anyway.

Wouldn't want any nasty suprises. But it is most likely the radius rod bush. Mine has been modified for god knows what and used to pull to the right when braking.

doug3rd Apprentice

doug3rd

Posted
  • Author
Posted

Thanks Joel, I'll check that out...

I don't know a lot about the ABS/traction control on the GTR, and the light didn't come on when I braked, but I am worried if something as expensive as this was the cause...

Does anyone know what the worst case scenario would be for this problem (pulling to the left when braking)?

predator Grand Master

predator

Posted
Posted

well if the steering control arm snaps or something while driving.. your steering will go completely out and this may result in a bad accident. At 80km/hr.. can be pretty scary. I remember I snapped an upper control arm after a tire blew out and i went over a curb at 70km/hr - trying to steer it back was a nightmare. If that happened while driving at high speed that could be very dangerous.

Otherwise.. you just be careful when braking till you get it fixed - maybe just the brakes need adjusting/bled, pads changed. I'd imagine it would be amplified at greater speeds (e.g. greater pull to left side or whatever at braking from say 100km/hr).. so just be bit carefl.

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by doug3rd

I in the market for a R32 GTR, and was almost ready to buy one car until I test drove it.  The ride was smooth and the engine great, but the car pulled slightly to the left.  

I figured that this might just be wheel alignment, but when I braked, the car really pulled to the left.

Is this a bad car, or is it just a case of bad wheel alignment and/or bad brake pad?

As far as I can tell, the car hasn't been badly smashed.  Is there anything else I can check?

Could be something as simple as a low tyre pressure which is amplified when you brake.

Or could be a chassis that is shorter on one side than the other....

Get a professional to check it. The causes are endless and without physically driving it , everyone is only guessing.

Cheers

Ken

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ToothDR32
      $5 Clock upgrade for R32 GTR

      By ToothDR32 · Posted

      Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...