Jump to content
SAU Community

Recommended Posts

Hey There

Recently got the rest of my bodykit which is Bn side skirts and Bn rear bar. A while back i got a Trust Front bar which we already fitted up but has not yet been painted. I thought id show the progres along the way with some before, during and after shots. Ill update as more of the work is finished.

Before Shots

post-26024-1181126349_thumb.jpg post-26024-1181127200_thumb.jpg

M-spec kit removed

post-26024-1181126550_thumb.jpg post-26024-1181126638_thumb.jpg post-26024-1181126808_thumb.jpg

Thats it for now :D

Edited by iLEC
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/
Share on other sites

Cheers Nismo Racer their Starcorp inpuls you prolly already knew there pretty common on the skylines lol

and mid life crisis you could have washed my car before i parked on your lawn haha

:D

Edited by iLEC
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3164658
Share on other sites

hi jake im ilecs dad

we had to remove a small amount of the rio bar for the cooler .but then had to remove some more to fit the front bar. there is a fair bit of it left tho. we did not remove completly like some people do we wanted to retain as much as possiable

cheers

we took very little away from the front bumper itself wasent any need too

Edited by mid life crisis
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3165386
Share on other sites

yeah its a mixture of a veilside rear with skirts and wing with a trail front bar. The skirts on mine were hard might have been a tad small so it hugs the car but srcrew it on as well.

I'll post some pics tomorrow as well

Edited by BreathLess
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3168985
Share on other sites

  • 1 month later...
yeah its a mixture of a veilside rear with skirts and wing with a trail front bar. The skirts on mine were hard might have been a tad small so it hugs the car but srcrew it on as well.

I'll post some pics tomorrow as well

Is there any problems getting the front bar off? My new M Sport front bar is getting painted today and was going to put it on myself...

Cheers

Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3257566
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...