Jump to content
SAU Community

Recommended Posts

Hey There

Recently got the rest of my bodykit which is Bn side skirts and Bn rear bar. A while back i got a Trust Front bar which we already fitted up but has not yet been painted. I thought id show the progres along the way with some before, during and after shots. Ill update as more of the work is finished.

Before Shots

post-26024-1181126349_thumb.jpg post-26024-1181127200_thumb.jpg

M-spec kit removed

post-26024-1181126550_thumb.jpg post-26024-1181126638_thumb.jpg post-26024-1181126808_thumb.jpg

Thats it for now :D

Edited by iLEC
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/
Share on other sites

Cheers Nismo Racer their Starcorp inpuls you prolly already knew there pretty common on the skylines lol

and mid life crisis you could have washed my car before i parked on your lawn haha

:D

Edited by iLEC
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3164658
Share on other sites

hi jake im ilecs dad

we had to remove a small amount of the rio bar for the cooler .but then had to remove some more to fit the front bar. there is a fair bit of it left tho. we did not remove completly like some people do we wanted to retain as much as possiable

cheers

we took very little away from the front bumper itself wasent any need too

Edited by mid life crisis
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3165386
Share on other sites

yeah its a mixture of a veilside rear with skirts and wing with a trail front bar. The skirts on mine were hard might have been a tad small so it hugs the car but srcrew it on as well.

I'll post some pics tomorrow as well

Edited by BreathLess
Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3168985
Share on other sites

  • 1 month later...
yeah its a mixture of a veilside rear with skirts and wing with a trail front bar. The skirts on mine were hard might have been a tad small so it hugs the car but srcrew it on as well.

I'll post some pics tomorrow as well

Is there any problems getting the front bar off? My new M Sport front bar is getting painted today and was going to put it on myself...

Cheers

Link to comment
https://www.sau.com.au/forums/topic/171716-bodykit-install/#findComment-3257566
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...