Jump to content
SAU Community

Recommended Posts

I did a search and couldn't really find what I am after.

When I start my car, there is a little puff of white smoke, and that's it. None when i'm driving or boosting, just on start up.

What would be causings this?

Also after that my exhaust has quiet a strong smell, it's had to tell what the smell is of - similar to burnt fuel, but this is constant.

I also had the car dynoed (not a tune or check, was just an open day dyno runs) and they said the car is runnin a bit lean.

What would this be from and how can it be fixed.

My Car is a 32 with a 26 conversion and remapped ecu.

white white smoke, oil, damaged turbo seal.

White steam smoke, blown head gasket due to running lean.

Possibly your injecotors are cloges, pump or fuel filter is on the way out

To test for head gasket, take it to a mechanic and do a gas analizer, this will tell you if there are any hudrocarbons in the radiator water.

To test for head gasket, take it to a mechanic and do a gas analizer, this will tell you if there are any hudrocarbons in the radiator water.

With the radiator, I am getting a new thermostat put in and the radiator fulshed, cleaned and new coolant put in.

Is there another way to check if the head gasket is or on its way to being screwed?

If the head gasket is screwed, what's a rough estimate to get it fixed?

Edited by URAS_33

when u start ur car is it early in the morning when its cold?? probs just the hot air hitting the cold air and creating the normal mist which all cars get when its freezing. Its funny how many people i know who got all scared that theyre car is puffing out white smoke when this is all that it is. just a lil food for thought. It may not be all bad. with the running lean probs ur fuel pump.

I did a search and couldn't really find what I am after.

When I start my car, there is a little puff of white smoke, and that's it. None when i'm driving or boosting, just on start up.

What would be causings this?

Also after that my exhaust has quiet a strong smell, it's had to tell what the smell is of - similar to burnt fuel, but this is constant.

I also had the car dynoed (not a tune or check, was just an open day dyno runs) and they said the car is runnin a bit lean.

What would this be from and how can it be fixed.

My Car is a 32 with a 26 conversion and remapped ecu.

A small amount of white smoke usually means the oil you're using is too light on start up.

Fuel smells nothing to worry about, probably just the seal to the fuel tank/pump, as it's known to perish on the r32 over time.

As for running lean that's bad... if you have a pfc or other ecu what knock reading are getting?

As for running lean that's bad... if you have a pfc or other ecu what knock reading are getting?

It just has the standard computer which has been remaped.

PFC is definatly the first on the cards and a good tune.

Yeah white smoke / steam is really faint and does disapate straigh away. I guess coz I'm new to the RB26 (only had a 25 before hand), I'm sketchin about every little thing thats goin on.

I also get white smoke on cold morning starts but i hope its due to LatinR33's explanation :P

Will have a proper look tomorrow morning if it lingers around or just disappears

Read from a site.

could be antifreeze when it is being burned it has a sweet type of smell and tends to dissipate in the air rather quickly
Sometimes when the head gasket goes it will produce a passage for the antifreeze to pass from the capillaries into the combustion chamber.
Answer 2

If the exhaust billows white smoke for a few seconds when first starting the engine after it has been sitting for a while, such as overnight, and then runs normally, it could mean that the rubber valve stem seals have perished - especially if the vehicle is a few years old and has done over 60/70,000 miles.

Another clue is: does the exhaust smoke smell like fresh, rather than burnt oil.

On cold engine starts, especially, the ECU will momentarily run a rich mixture to get ignition going, then thin it back to normal once the O2 sensor can get an accurate reading. The puff of 'smoke' probably has a sweet smell and would contain a small amount of poorly combusted fuel, some uncatalyzed exhaust, and likely a bit of condensation.
Remember it this way--if the white smoke doesn't go away, THEN you have a problem. If it disappears after a few minutes, it's just water vapor. Part of the chemical equation for the combustion of gasoline includes H20.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...