Jump to content
SAU Community

Old Pac

Craved

By Craved,
in New South Wales

 Share

Recommended Posts

scathing Grand Master

scathing

Posted
Posted
Also they were saying the driver was found to be under influence???

Yeah, apparently he was on pot and booze.

But he didn't crash into a tree on the side of the road. He fell down a massive f**king hole in the middle of it. Trying to use his intoxication to defend the government's criminal negligence occasioning death is just wrong.

Link to comment
https://www.sau.com.au/forums/topic/172015-old-pac/page/2/#findComment-3658764
Share on other sites
scathing Grand Master

scathing

Posted
Posted
Exactly.

"Oh if he wasnt under influence, he could have pulled up in time"

yeah right, they werent there, they wouldnt know that, stupid government

Hmm.....

Mr Menzies said medical toxicology evidence would later be given that would show Mr Holt, who was driving the car, had a blood alcohol level that was "marginally above the legal limit" and had ingested cannabis.

Referring to the cannabis, Mr Menzies said: "And that amount could well have had some effect on Mr Holt's capacity to stop the car before this accident occurred."

Undoubtedly it could have had some effect on his capacity to stop the car. Alcohol and cannabis are known to affect people's reactions and co-ordination.

But you know what else had an effect on Mr Holt's capacity to stop the car before the accident occurred? A massive hole in the f**king ground that didn't used to be there. If there was no hole, he would have stopped without falling into rushing water. Actually, he wouldn't have even needed to stop, and that would have removed the possibility of an accident altogether.

Paul Menzies can go f**k himself.

Link to comment
https://www.sau.com.au/forums/topic/172015-old-pac/page/2/#findComment-3661837
Share on other sites
  • 3 years later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...