Jump to content
SAU Community

Recommended Posts

I think it all really depends on what the purpose you have for the car is. If you are after basic/intermediate levels of tuning for street and the occasional track day, it's tough to go past the PowerFC as it's pretty much plug n play and can do nearly everything most people want.

If you want the best of the best and have the $$$ for it, you're definitely looking at either the Autronic or the Motec ECUs. Both have more parameters and controls than you could ever use but neither are plug n play and take plenty of time to install, tune and properly setup if you want all the goodies.

Have a look at the following threads for more info:

http://www.skylinesaustralia.com/forums/in...tronic+power+fc

http://www.skylinesaustralia.com/forums/in...r%20fc&st=0

http://www.skylinesaustralia.com/forums/in...p;#entry1024327

http://www.skylinesaustralia.com/forums/in...mp;#entry931292

http://www.skylinesaustralia.com/forums/in...mp;#entry716558

That should keep you going for a little while otherwise try using the search option in the top right of the menus.

you sound confused

i think you mean to wish to remove the factory airflow meters

600hp is fine with airflow meters

but if you insist motec and apexi powerfc will support no airflow meters

safc II will not support no airflow meters and wont go anywhere near 600HP

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Small update for the day... Turns out the intercooler and engine coolant hose kits are anything but complete....I probably should have counted better but it only really covers about half the coolant hoses in the car, it really just covers the visible stuff and pretends everything else doesn't exist (turbo water feed and returns and also heat exchanger lines through the 2 pumps and cooler) .In any case, I'm happier to have half reliable hoses than none, but a bit of a disappointment. Anyway...finger click (and 5 hours).....hoses in place, lots of spring clamps replaced with screw clamps, and engine coolant is on the pressure tester for the night.   Incidentally, upsized header tank is an Inifiniti factory option....not sure I'll ever do prod car racing in this but at least it is legal.
    • Just weld it onto the hot pipe. If you want it right after the turbo, put it right after the turbo. Or rip the comp cover off and drill and tap a hole into it.
    • hahaha glad I can rely on you two to go on a spiral at the drop of a problem! Some quick answers....the ducting is excellent top bottom and sides....everything that gets in goes through the coolers (noting the oil cooler redirects it out again, fair call if it is cooling 120o+) and the heat exchanger for the intercooler also has some scoops to pick up more than it's fair share too. I can't see going down the water spray track....no bueno for formal racing and a big risk for long rally days if you run out (plus I'm not clear if it is allowed there either yet).   Frankly, it must be possible to reliably put 400kw through a standard front end, the BMWs do it so I just need to work it out....I'm starting with reducing blockages in the way and adding some coolant capacity with a bigger header tank, flushing rad and making sure it was filled/bled properly (I didn't do the last coolant change); also taken measurements incase next step is a bigger/higher capacity custom radiator
    • wow, a completely stock GTR! I've got to admit, I have no idea from what you are describing....do you have  any idea where the "thump" comes from, and are you certain it is the HICAS light not something else like the cat overheat light?
    • nice work, welcome to the world of CAD! fabricating accurately in 3 dimensional space is beyond me....I almost always end up making something more than once...sorry I mean I extensively use prototyping
×
×
  • Create New...