Jump to content
SAU Community

Recommended Posts

  • 3 months later...
  • Replies 539
  • Created
  • Last Reply

Top Posters In This Topic

Just read your post from start to finish. 

Good to see the progress from start to finish. 

Did you go bigger in the injectors from the 800 odd cc ones. 

I have a similar setup with the gtx3582r and 1000cc injectors with a 3l built bottom end ported neo head s2 pon cams.

Currently on run in tune. 5000 rpm limit  14psi i see 349rwhp so 260rwkw with no timing as had a problem with the tps. On pump 98. When its run in i will be throwing bigger injectors at it  ew ecu instead of the nistune. 

Hopefully see around 480 to 520 on pump and 600ish on e85. Still debating on the e85. 

All built by myself. Including my own exhaust manifold and 3.5 inch dump pipe and 3 exhaust that i made. 

Bare in mind i have it in a lc gtr torana that tips the scales at 1057kgs. 

20160808_163908.jpg

Resized_20160909_141859.jpeg

20160921_190821.jpg

DSC_8294-Edit.jpg

  • Like 2

Injectors are rotchester 1000cc that flow 1090cc .the e85 road is a good one but its best to keep up your maintenence and not the best to leave your car sitting around for long periods . Also found once you start climbing higher coil packs and harnesses need to be good order .

But with the weight of your car you will shit your self the first couple of times you hit it ...lol if you get a chance to run a 1000 meter event you have some fun in that car.

My next step once i find my other problem out is to run nos again so that 500kw that marko is talking about be achievable i hope . Good luck with the let us know how you go.

 

 

12 hours ago, lcxu105 said:

Just read your post from start to finish. 

Good to see the progress from start to finish. 

Did you go bigger in the injectors from the 800 odd cc ones. 

I have a similar setup with the gtx3582r and 1000cc injectors with a 3l built bottom end ported neo head s2 pon cams.

Currently on run in tune. 5000 rpm limit  14psi i see 349rwhp so 260rwkw with no timing as had a problem with the tps. On pump 98. When its run in i will be throwing bigger injectors at it  ew ecu instead of the nistune. 

Hopefully see around 480 to 520 on pump and 600ish on e85. Still debating on the e85. 

All built by myself. Including my own exhaust manifold and 3.5 inch dump pipe and 3 exhaust that i made. 

Bare in mind i have it in a lc gtr torana that tips the scales at 1057kgs. 

20160808_163908.jpg

Resized_20160909_141859.jpeg

20160921_190821.jpg

DSC_8294-Edit.jpg

That is a very nice conversion but I am biased as well as I have a soft spot for toranas :)

  • 1 year later...
31 minutes ago, WARLORD said:

Thanks

car still providing boners? haven't heard about it in a while!

Also these days, the Bosch 1550cc aka 1650cc (as most retailers call them) are 100% unmodifed where as the 1250cc are still milled to get that flow rating.

yer car is still around just haven't had time to play with it ... I am thinking of reconnecting the nos again with a 75 shot  for something to do but i know the clutch will die. need to find a new clutch,

That will be clutch number 6 since 2006 . ive tried so many types now and only found the jim berry to have lasted my abuse i should of keep it.

2 hours ago, WARLORD said:

yer car is still around just haven't had time to play with it ... I am thinking of reconnecting the nos again with a 75 shot  for something to do but i know the clutch will die. need to find a new clutch,

That will be clutch number 6 since 2006 . ive tried so many types now and only found the jim berry to have lasted my abuse i should of keep it.

may use the nitrous to only get the turbo  on, as a form of anti-lag - would make it like a V8

You still on a single plate? maybe have a chat with Scott at Western Clutch in St Mary and pop in a twin plate.

got a os str twin and i think i have over heated the pressure plate  after killing a lambo and a mclaren  

 

are they good rebuilding clutches 

Edited by WARLORD
3 hours ago, WARLORD said:

got a os str twin and i think i have over heated the pressure plate  after killing a lambo and a mclaren  

 

are they good rebuilding clutches 

They have the right tools to do what you dream of, they have a clutch pressure plate testing tool as well!

I've got a Exedy clutch modified by them to clamp 1.7 tons with a carbotic disc and the pedal effort is like a stock manual Corolla.

27 minutes ago, WARLORD said:

how much for this new addition 

Somewhere around the $1k mark installed (this was a while ago) - yours might be different in price as it's a twin plate

  • 8 months later...
  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...