Jump to content
SAU Community

Recommended Posts

hey all.

happened yesterday and today.. theres something howling when driving for the first 2-3 mins.

i normally warm my car up for about 2-4 mins.. the oil pressure drops from about 7bar to 4 bar and th revs dropped a bit.. like normal.. and i drove off.. careful not the get the boost gauge newhere close to 0.. shift at 1500 or so..

yesterday it howled abit more.. cos i didnt let it warm up.. only like 2 min warmup. this morning was kinda intermittant cos i let it warm up for jst about 4 min.

im sure its not a leak as we tightened the fmic piping up properly.. i double checked it when i got home on the day of the install.

it boosts fine tho.. no lag etc.. only happens when the cars coldish..

any input on what the noise could be?? kinda has me worried as the cars only done 85xxx k's and im the first owner.

My mods:

Full exh

6*3*80 HDi FMIC

Apexi Powerflow

Factory boost solenoid (low - 7, high - 12-14psi) NOTE: i HARDLY use high boost, if i do its only for a few seconds then flick it back to low.

i hardly boost my car. no really.. i hope its not my turbo but something tells me it is.

Link to comment
https://www.sau.com.au/forums/topic/173073-turbo-howling/
Share on other sites

NOTE: it is also getting very cold here in auckland. im talking below 10degrees cel. it must hav been about 2-5 degrees yesterday and this morning..

my mate thinks its the vortex thing happening with my powerflow filter? going to check for shaft play after work today. fingers crossed!!!

Link to comment
https://www.sau.com.au/forums/topic/173073-turbo-howling/#findComment-3183070
Share on other sites

Howling probably isnt the best description... hmm..

Does it do it on idle if you rev it?

Or only under load?

Where is the noise coming from, right/left side of the enginebay?

Anything you might be able to provide will make it easier.

It sounds like a leaky cooler pipe to me, but everyone describes noises differently :D

Link to comment
https://www.sau.com.au/forums/topic/173073-turbo-howling/#findComment-3183225
Share on other sites

i vote for exhaust gasket leak, without knowing the definition of "howling".

common issue with the lock tabs not working or breaking on the turbo flange bolts. But some answers to R31Nismoid's question will help the diagnoses.

Link to comment
https://www.sau.com.au/forums/topic/173073-turbo-howling/#findComment-3183824
Share on other sites

cheers so far guys.

it only happens when i drive it in the cold.. its been around 2-5 degrees here lately so blooody cold.. thats it.. only for a few mins.. i checked all the fmic piping again last night.. all tight..

i doubt its the exh mani tho cos i never touched it..

i checked the turbo wheels for shaft play and it seemed sweet.. no play at all.. to be oversensitive, id say the bearings were a weee bit noisy but thats it.. i cud hear it when i spun the wheels with my fingers.. it boosts fine.

Link to comment
https://www.sau.com.au/forums/topic/173073-turbo-howling/#findComment-3184245
Share on other sites

+3 to turbo gasket leak.. after putting my big front pipe on and having to perform some percussive maintenance on the dump pipe bolts.. take car for drive at over 5000rpm it sounded like there was a banshee under my bonnet. Tightened all turbo>manifold bolts and the banshee died :D

Link to comment
https://www.sau.com.au/forums/topic/173073-turbo-howling/#findComment-3184866
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's awesome. Fully serviced/full log book history for one of those cars is super rare from what I know. With JDM's like Skyline's, Supras, are quite hard to find one with full log book history. S15's seem to be somewhat of an exception, at least the spec s australian delivered models.
    • Hey all, It's been a bit since I have been able to update.  I pulled the fuel pump, first off it was a "universal" pump and the strainer was very clogged, and it was folded over on itself.  I replaced the fuel pump and all is well....  No more stalling.
    • That's convinced me I'll bump up the G30-660 to 770   Any idea if the difference in boost pressure? Cheers
    • When: Saturday 24th of May 2025 - All day Where: Sydney Dragway, Eastern Creek Cost: Varies - Book direct with the GTR Festival Website We will be there on the day with a stand please reach out via our interest form if you wish to help out with the stand. Limited parking will be available in the display area, first in first served with current members getting priority, please register your interest with the link above also. Please post any great photos you take on the day on this thread and we will try use some in our e-mails/website/social media
    • Hey guys so turns out this project is going to be much bigger than I thought haha but I've done some my homework and have done a few panels on my car, but one part I can just not visualise is this. If I do a spot repair and I put filler in a dent for example and sand outside of the repair with 320 grit lets say so the primer can stick as I will only put primer on that repair and the surrounding area and then repaint the whole panel. Don't I need to make sure that I don't put primer on the old clear coat? I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down, it's still shiny. I thought putting paint on clearcoat or primer on clearcoat is a bad idea because it won't stick. So in this scenario it's a bit different to mine but imagine someone doing a spot repair and only painting that small section of repair but the new paint is landing on the old clearcoat. What am I missing?
×
×
  • Create New...