Jump to content
SAU Community

Recommended Posts

There is a warning that flashes on my dash right beside the handbrake light and it looks like a "chevrolet" badge with wavey lines or steam coming off it. I have just recently had a replacement auto fitted and a bit of hyd fluid was lost from the back of the auto from a resevoir. It is still within the Min-Max range, not sure if this has anything to do with it. Automatic shop (very reputable) did not know what it is. It looks like an oil pump for the variable 4WD system, does this have anything to do with it. Has a 3 core radiator fitted, is this the overheat light, shouldn't be hot. Any ideas what this is.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/
Share on other sites

YEP, definetly number 12. I had to cut the temp sensor wire that comes out from under the mid floor to the second cat convertor. But that was a while ago. Should of seen the light since then. Thanks heaps for that info. Other than speaking Japlish, does anybody know what to do now.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3190743
Share on other sites

I am gonna go out on a limb and suggest its the attessa pressure cylinder that you are talking about? The pump for it is actually located at the back above the rear diff. The fill pot for it is inside the cargo area on the drivers side behnd one of the natty little panels in the side. As with all auto fluids, this should be checked with the car warm, running and parked on level ground. Do a search for the actual fluid required or have a look in the DIY sticky at the top of the forum.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3191431
Share on other sites

so maybe the O2 sensor is letting too much fuel in and causing it. It seems to be "heavier" again than it normally is. Like lucky to touch 300kms around town now just city driving. Used to get 350 - 400kms. So is this also measured at the o2 sensor aswell and whats the best replacement.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3191623
Share on other sites

The transfer case pump uses Auto trans fluid and is filled in the resoviour in the boot, the transfer case itself also uses ATF and is filled through a filler on the rear of the gearbox.

I think the engine check light can come on in circumstances other than just cat too hot right? If you've cut the wire it can't be cat temps....better check that out maybe search outside stagea section for it.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3193804
Share on other sites

Don't mean to hijack thread, but what warning is no.15? Mine came on everytime I got up to 160ish and released back to 100ish. Would stay on for anywhere between 5-15secs and then turn off. Also came on while stationary once.

You need to get a consult interface onto that to check the error codes... Most mechanics should have one and the stagea should be listed.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3201868
Share on other sites

There is a warning that flashes on my dash right beside the handbrake light and it looks like a "chevrolet" badge with wavey lines or steam coming off it. I have just recently had a replacement auto fitted and a bit of hyd fluid was lost from the back of the auto from a resevoir. It is still within the Min-Max range, not sure if this has anything to do with it. Automatic shop (very reputable) did not know what it is. It looks like an oil pump for the variable 4WD system, does this have anything to do with it. Has a 3 core radiator fitted, is this the overheat light, shouldn't be hot. Any ideas what this is.

that "chevy" looking light is surpose to be a pic of a cat conveter over heating. on my friends cars a s13, a cefiro and a cellcier all had this light come on, they all shared a comon problem. Bloocked Catilitic Conveter's. you can take yours out and either replace it. Smash the middle out with a screwdriver (illigal. 5 thousand dollar fine, but only if you get caught) or you can tap it on the ground to lossen the dirt and blow it out with compressed air. and get somone to hook that wire back on could be shorting out and making the light come on

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3205864
Share on other sites

The wire you are talking about seems to be a capillary/mechanical setup, so there is no rejoining it seeing as though it has been cut at the "cat". The light seems to have stopped again, I think I need to replace the O2 sensor anyhoos. Not getting a reading off the wires at the plug, except for the 12 v power wire. If it is the cat that is blocked, seems funny that the wire would give me a reading, unless it was the 02 sensor signalling the dash light.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3209677
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...