Jump to content
SAU Community

Recommended Posts

I don't know much about clutches, but i'll reply anyway. You say you smell burning whenever you go hard? Well it could be your brakes, if you're braking heavily or alot when you're going hard. If your clutch is not working good, as far as i know it will slip alot, and that's how you can tell if you need a new one. Exidy clutches are supposed to be a good brand also.

That's all i know :D

Ryan

Link to comment
https://www.sau.com.au/forums/topic/1740-clutch-done/#findComment-33089
Share on other sites

The clutch will slip in higher gears (lower too - but not as obviously i think) .. like you'll put your foot down and the car will rev and you wont gain speed... you'll notice it.

If you continue to let it slip for a long time, you can damage the flywheel, but thats about it (i think) eventually the car will be undrivable..

mine went not long ago and i have a 5 puck brass button clutch in there now - absolutly fantastic!

Christian

Link to comment
https://www.sau.com.au/forums/topic/1740-clutch-done/#findComment-33112
Share on other sites

  • 2 weeks later...
Originally posted by PranK

The clutch will slip in higher gears  (lower too - but not as obviously i think) .. like you'll put your foot down and the car will rev and you wont gain speed... you'll notice it.

If you continue to let it slip for a long time, you can damage the flywheel, but thats about it (i think) eventually the car will be undrivable..

mine went not long ago and i have a 5 puck brass button clutch in there now - absolutly fantastic!

Christian

I think theres a chance that you flywheel can shatter too. I drove

my to the point where it just wouldn't move anymore, not that

I'd recommended such an action. :) Smelling your clutch through

the air vents is a definate sign.

Link to comment
https://www.sau.com.au/forums/topic/1740-clutch-done/#findComment-39517
Share on other sites

full face organic just means that it is like the stock clutch plate, i.e full face and made from organic material. You should specify a higher pressure plate like 2400lbs or such and maybe even steel backing on the clutch plate. As for driving the car with a slipping clutch, I did it and was shocked when we pulled it out. The actual clutch/friction plate was fine and had heaps of meat left but the pressure plate and flywheel where toast. It is not a good idea to ride a button clutch. :(:P

Link to comment
https://www.sau.com.au/forums/topic/1740-clutch-done/#findComment-39749
Share on other sites

Alot of people have said it's a good clutch. Mine's basically a

custom one. Everytihng is Exeidy Dakien Full Faced Organic

except for the compound used. Pressure plates a bit heavier

too. It's supposed to be slightly stronger. I think it's a bit too

strong now cause I think the next thing to go on my car is my diff,

bit harsh on the takeoff. So I think it would be perfect for the 33.

Just remmeber to bed it in properly or you will regret it later.

Link to comment
https://www.sau.com.au/forums/topic/1740-clutch-done/#findComment-39881
Share on other sites

Here is my clutch story -

Had a std clutch in R33 which I killed in about 3000 kays.

Then put in a single plate nismo one which lasted about the same.

Then I had to replace the gearbox & fitted a twin plate OS Giken.

I had trouble at the drags with this one slipping at the top end, so

we fitted a triple plate OS Giken clutch.

Then I blew up the gearbox (a Trust 6 speed!) doing burnouts in 2nd gear.The clutch still looked okay at this stage but one of the plates was starting to go blue more than the others.

When I blew up the engine at the 4.6.&Rotary Nationals in Adelaide in Feb, we replaced the engine with a OS Giken 3 litre.

The crank in this engine has 8 bolt holes for the flywheel(not 6)

so I had to change the clutch again!! Now I have a Quad plate,

Chrome moly, 8 bolt OS Giken clutch. I'm sure this one will last.

Moral of the story - Get the right clutch for your application first up

PS. At Drag Combat in May I completely smashed the std rear driveshafts in 2 places and have since replaced them with HKS

shafts. When the gearbox came out for a checkover the clutches

in the transfer case were fried 'cause I backed off the startline using Fwd only.

I now have a fresh transfer case, a fresh gearbox, HKS shafts front & rear, & a hydraulic torque split controller so all 4 tyres

better look out now!

Link to comment
https://www.sau.com.au/forums/topic/1740-clutch-done/#findComment-40742
Share on other sites

Originally posted by Zahos

Hey ex-static

If u dont mind me asking, where are you getting the clutch done, and approx how much $$ is it going to set you back?

Zahos

I got it done at Ice Performance in Cheltenham, its an excellent clutch, very light, and very grippy! I highly recomend it.

-ex

Link to comment
https://www.sau.com.au/forums/topic/1740-clutch-done/#findComment-41124
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...