Jump to content
SAU Community

Volk F Zero Winning Wheels 18x9 And 18x10

made_guy
 Share

Recommended Posts

made_guy Experienced

made_guy

Posted
Posted (edited)

Item: Volk Racing - F Zero Winning 18s

Specs: 18x9" +35 18x10" +35 114.3 Suit GTR

Price: $1000 ono no tyres

Location: Gold Coast - Pick Up most definitely preferred

Condition: Good - couple of gutter marks and the fronts have a bit of 'inner' wear from scraping strut on full lock ;)

Reason for selling: Don't fit my GTSt neatly without mods and they're not my ideal rims so I can't be bothered making them fit

Contact: Dane 0404837187 or PM or in the thread if it's a question that others may also be wondering :(

As stated, this won't fit a GTST with stock gaurds etc. The fronts don't actually stick out past the gaurds, but the inside can scrape the strut when on full lock.

Also the rears stick out the tiiiiiniest bit on my GTST which is almost negligible, but unless your gaurds are rolled, you'll get nice little stringy bits coming of your tyres when making a 'g' or two around turns - unless you dial up some serious camber i suppose.

Oh and one of the rears had a little buckle in it (thanks must go to the previous owner for failing to mention that to me when i was asking about their condition... :) ) But it is currently getting fixed by depulu wheels and I'll even give you the receipt for that repair.

Here's the pic from the original listing from where I bought them, but I will get some more pics tonight of each rim (well the 3 that I have in my posession currently at least)

Pics (left to right): 1) pic from original listing...not sure which wheel that is? 2) rear left 3) front right 4)front left

post-37671-1182734048_thumb.jpg

post-37671-1182767122_thumb.jpg

post-37671-1182767162_thumb.jpg

post-37671-1182767181_thumb.jpg

Edited by made_guy
made_guy Experienced

made_guy

Posted
  • Author
Posted (edited)

Update:

Got the 4th wheel back and it is perfect!!!

except for the little mark that i put on it taking it out of the boot when i got home :D:laugh: which you can see in the photo. also there is some overspray on the rim itself that you can see (i'm a bit annoyed cos i liked the anodised blue even though you can't see it with tyres on them..

so here it (they) is ready to go:

post-37671-1184405578_thumb.jpg

post-37671-1184405632_thumb.jpg

Edited by made_guy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...