Jump to content
SAU Community

Recommended Posts

hey all i know there is about a billion threads already on this but ive read em all and followed all the suggestions but i still cant get my car to start.

when i first instal it all and tryed starting it up it run but i turned off cuz lots of smoke coming outa bonnet (new heat wrap). car started again after this, the idel was all over the place and hunting bad.

turned the car of and went in for eats.

came back out tryed starting and nothing

the injector duty is only at 1.1 when it starts cranking then goes done the long you crank it...

some1 plz help me

ben

Link to comment
https://www.sau.com.au/forums/topic/175060-d-jetro-issues/
Share on other sites

turn the car to ON but dont start it

look in ETC, SENSOR SW CHECK

do you see any sensor names highlighted in black ?

if so what are they ?

have u checked and spliced the map sensors?

where did you phsyicall install the map sensors?

Link to comment
https://www.sau.com.au/forums/topic/175060-d-jetro-issues/#findComment-3209026
Share on other sites

um map sensors in cylinder 3 and 4, 555cc injectors. nothing highlighted

dont know how to put areflow meters to djetro

ben

Mate i think you should have a good read of pauls FAQ's before something gets damaged

Are the map sensors hooked up after the throttles(right near the head)

Edited by Adriano
Link to comment
https://www.sau.com.au/forums/topic/175060-d-jetro-issues/#findComment-3209068
Share on other sites

well sorta found out the problem, set the shit up for diffrent injectors and changed plugs and went fine.

drove it and when put foot on the gas it splutted a bit and died, wont start again same as when plugs were f**ked.

least i know its something to do with the fuel. will jsut have to save and get it tuned

ben

Link to comment
https://www.sau.com.au/forums/topic/175060-d-jetro-issues/#findComment-3212512
Share on other sites

Ben's asked me to ask a few questions, Suggested to ben to buy some new plugs,, fixed the starting problem..

im having trouble finding the lag time for Nismo 555cc.. i think its 0.73 but i need correct numbers.. or is it 0.71 anyhow.. the car is not registering more than 10% or so inj duty.. im thinking that because its map based sensors and not Maf based .. there is no base map for this version of the power fc.. which would mean its not sure how to " GO" because its not been programed to covert the map signals into something useabble.. is this correct??

realistically does it need a tune before it should be test drivable.. or should the engine be capable of atleast moving up and down the driveway without flunking out..

the car wont start again.. im assuming we have roasted the plugs again. too much fuel could the Sard fuel pressure reg be up too high?? any help would be greatly appreciated..

Thanks Guys

Link to comment
https://www.sau.com.au/forums/topic/175060-d-jetro-issues/#findComment-3212546
Share on other sites

no i mean side, there is a bottom side and i little line from top

ben

there are 3 hoses. the top one is vacuum/boost. the one on the side is fuel in (from rail), the bottom one is fuel out (return to tank).

and yes you need to check the pressure of the fuel reg. it should be 3 bar base pressure (no vac or boost).

Link to comment
https://www.sau.com.au/forums/topic/175060-d-jetro-issues/#findComment-3212609
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...