Jump to content
SAU Community

Fixing Gutter Damage To Rims.

LatinR33
 Share

Recommended Posts

LatinR33 Experienced

LatinR33

Posted
Posted

anyone have their rims restored and fixed all there gutter scrapes. Did you guys take them to a proper mag shop or have one of those mobile paint companies come to your place to fix them. any clue on how much they charge so I dont get ripped thanks.

Link to comment
https://www.sau.com.au/forums/topic/175524-fixing-gutter-damage-to-rims/
Share on other sites
zebra Grand Master

zebra

Posted
Posted (edited)

Lol I think My rims would need more than that....I read an article in zoom about a place that did it and they also welded up big chunks that were missing....might try and find the magazine (fingers crossed)

Duncan which shop did you use if you remember and what cost roughly?

Cheers

Edited by zebra
4drftn Experienced

4drftn

Posted
Posted

an engineer will put the wheels on a metal lathe and machine down the lip until its flush... they do a good job too...

as far as scratches on the rest of the mag if they are alloy a bodyworks can fix them by filling scratches and large gowges with a good body filler and hit it with 2k paint... 2k being quite hard... will bring it up nice and new looking... as long as they match the colour up well to suit the other wheels.

cost for engineer can be very exspensive.... but if you ring around you might get someone to machine lip for around $70 - $100 a rim (depending on size too, anything over 17inch will be to big for many lathes

bodyworks will fix scratches and gowges for around the same price...

depending on how damage your rims are you might need to do both...

are they bent? if impact has happened it may be out of round...

godzl1975 Experienced

godzl1975

Posted
Posted

there is a guy in ingleburn industrial area if your in the campbelltown area his pretty good and cheap as well...got my work rim done when i turned into the gutter n left about a 1cm dent...think it was $60 with pulling tyre off and re balancing it.

found it in whitepages:

All Mag Wheel Repairs Pty Ltd

Repairer-All Major Insurance Companies

Unit 2/ 39 York Rd Ingleburn 2565

(02) 9618 1300

WARLORD Veteran

WARLORD

Posted
Posted
anyone have their rims restored and fixed all there gutter scrapes. Did you guys take them to a proper mag shop or have one of those mobile paint companies come to your place to fix them. any clue on how much they charge so I dont get ripped thanks.

I always us the magman 2/21 moxon rd punchbowl 9709-2686 greg boness is one of the best around. ive taken some real f***ed rims there that i have bought for peanuts and they look new when he's finished.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Rear subframe stay bracket bolt removal issues

      By MBS206 · Posted

      TBH, it sounds like the threads on the bolt are fubar in a specific section. Most likely as you've been working it back and forth it has torn threads out, as you loosen the bolt, this section enters the nut, now you're spinning a round shaft inside the nut, there's no threads here.   Use something similar to a claw on a hammer that will fit either side of the bolt head and try to apply downward force while also undoing it. The idea is to attempt to catch a thread, or just rip the f**ker out. Caution on ripping out, as it could bend/maime/mangle what the captive nut attaches to. If the captive nut is actually okay, you could do the dirty part of cutting the head off the bolt, then cut a slit in the end of the thread that's now exposed and then screw it up and into the area the captive nut is until it falls out the other side. However, this does risk the remainder of the bolt rusting over time and damaging near the captive nut and also making it rust. However, so can cutting pieces of panel work out to access this area if you don't reseal it properly.
    • MBS206
      Rb25 det nitto washer crank gear

      By MBS206 · Posted

      Well, every piece of information on that part when you track it back to Nitto says it's for a KIT of theirs. It is also designed thicker to be stronger. And they speak about a specific harmonic balancer bolt they supply for the whole setup.
    • MrStabby
      Rear subframe stay bracket bolt removal issues

      By MrStabby · Posted

      Techniques for removing stuck bolts are: hitting the bolt head with a hammer, heating the bolt to red hot then letting it cool and working it back and forth like you are already doing. AFAIK the idea is to try to crush whatever material is stuck between the threads (and heat also melts locktite but that's almost certainly not relevant in this case).
    • GTSBoy
      Rb25 det nitto washer crank gear

      By GTSBoy · Posted

      Yuh, I think it works with the Nitto gear only. I presume that you're not also using the Nitto gear? Watch the video. Compare the interface between the Nitto gear and washer (on the gear side) vs the stocker and decide if you think the Nitto gear is different from stock there.
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Liking the new charger, battery all good (I think).   Also like how you can put it in power supply mode too. Will troubleshoot with that sometime soon.
×
×
  • Create New...