Jump to content
SAU Community

Recommended Posts

i have a 1998 semiauto r34 gtt. with intercooler, airfilter, BOV .and i drive it normally.but it just can keep going for about 280 km with a full tank.

i use #98 petrol, and fill in about 48 liters to make it full when the indicator tells me there was few petrol. is the fuel tank of gtt 50L ? i just want know a normal situation of the gtt's fuel consumption thanks a lot.

i have a 1998 semiauto r34 gtt. with intercooler, airfilter, BOV .and i drive it normally.but it just can keep going for about 280 km with a full tank.

i use #98 petrol, and fill in about 48 liters to make it full when the indicator tells me there was few petrol. is the fuel tank of gtt 50L ? i just want know a normal situation of the gtt's fuel consumption thanks a lot.

Hey Dude I have a R34 GTT tiptronic auto Hybrid fmic, full exhaust from turb back,Greedy ebc, Safc2,BOV, POD, and my car gets 300 km to a full 50 lt tank it sucks what is wrong ????????????????? :thumbsup:

Edited by YPLAY4
i have a 1998 semiauto r34 gtt. with intercooler, airfilter, BOV .and i drive it normally.but it just can keep going for about 280 km with a full tank.

i use #98 petrol, and fill in about 48 liters to make it full when the indicator tells me there was few petrol. is the fuel tank of gtt 50L ? i just want know a normal situation of the gtt's fuel consumption thanks a lot.

its all in how u drive the car keep it off boost and u will do fine. i have a r32 gtst with fmic dump pipie full exhaust stock cat uped boost pod filter. and i get 450 to 500 normaly but when i give it some i get bout 300 to 350 and thats not even on empty.

GTT tank is 65L. If you used 48L to top up then you have approximately another 17L left. 280kms to 48L is still pretty rich. I just filled up my tank today with 47L after having done 360kms.

The usual culprits are O2 sensor, spark plugs, AFM...perhaps take it for a tune and service.

NISMO is right, the tank is about 65L. I'll normally get about 400kms region to a full tank. I don't run it till the lights come out though. Got a 3" turbo back, fmic, pod, ssqv, boost at 12psi, foot is a little heavy at times :nyaanyaa:. Really depends on how you drive.

changing the o2 sensor will help, changed mine and i went from 300km a tank to about 430km tank.

This sounds more like it. I have a s2 stagea (r34 engine, gearbox), which is quite a bit heavier than a skyine and on 48L my car will get over 400km around town. Its got 160awkw too so its not stock either.

My guess is that you should at least be getting more than 350km on this amount of fuel, modified or not. If its doing less than that, you need to either adjust your driving style or look for whats causing the problem - eg. check your O2 sensor. :D

A good free-flowing exhaust, SAFC or similar, and improved ignition timing will help your fuel economy as well, not to mention a bigger turbo (off boost while cruising). :D

As others have previously mentioned, the fuel capacity is 65L so try pumping it as much as possible. Reducing the use of boost should help acheive more k's. If not u better get it checked out.

my 2c worth

the following could be causing it too

Dirty air filter - causing the motor to work harder than it needs to , cause its not getting the airflow it needs

Slightly too thick oil - are you using the correct grade of oil in it ? I mistakingly used some stuff that was too thick in another car I had - and I did notice a drop in economy

change the o2 sensor as previously advised

have you ever had the car on a dyno? the dyno readout of AFR can definately tell you a LOT about what your motor is doing. I think if you were chasing the most kays per tank .. an after market ecu or a few add in mods like a SAFC and a SITC ( I think thats the one that controls engine timing )

if you got the above fitted . and spent some time and money on a dyno tune.. you would probably get more power and use less fuel. dont forget if a motor is running really really rich .. then its safe.. but .. its just pissing fuel out the tail pipe , leaning the mix to a leaner (yet still safe ) will yeild more power and less fuel consumption - but dont fall into the trap though of getting a bit more power and driving like a maniac - cause of course your goign to use more fuel

good luck matey!

if you can afford it run with a good fuel like BP ultimate 98 - just less chance of it pinging/detonating if you push it hard.

Oh and .. have a look around .. because you can find " equivalent " o2 sensors that are usually less expensive. To be honest I am not 100% certain if the equivalent o2 sensor will be " just as good" as a geniune one. But its worth a go.

Make sure you get some good crimp connectors to join it up , as my previous experience with this proved that the wires they use on o2 sensors are impossible to solder ( I think they are stainless? )

thanks everyone .now i think i catch the key point.

another question : which grade of petrol should the gtt fill? #98?

thanks everyone .now i think i catch the key point.

another question : which grade of petrol should the gtt fill? #98?

As this had been covered many many times, anything just 98 Octane will be just fine. Be it BP Ultimate, Caltex Vortex 98, Shell V-Power, V-power Racing, Mobil Synergy, they are all fine. Just a personal preference on which 'BRAND' one prefer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The roof is wrapped
    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
    • The downside of this is when you try to track the car, as soon as you hit ABS you get introduced to a unbled system. I want to avoid this. I do not want to bleed/flush/jack up the car twice just to bleed the f**kin car.
    • But again, the engineers said your cast aluminium would be fine based on the load that would be stretching that section. Same load stretching the bolts in a flex (not the twist), with a much smaller cross sectional area than the original part you've broken. It's why you'd need to be using higher strength bolts, but that's just making up for the strength you lose with less area...
×
×
  • Create New...