Jump to content
SAU Community

Recommended Posts

The engine is out of my r33 gtst that went 10.5 @ 125mph a couple of months ago, new setup is being built so this stuff has got to go!

RB25 long motor, sump to rocker cover, has forged pistons, shot peened rods, prepped crank and block, ported head, genuine nissan head gasket, tomei 256degree poncams, tomei exhaust cam gear. this engine made 480rwhp with 24psi through a gt3540. runs perfect and comp tested perfect before being pulled out of the car. $5000 or very close offer!

polished plazmaman plenum, bolt's to standard runners, 600x300x75 intercooler with polished alloy pipes and turbosmart bov to suit the plazmaman plenum, incuded is the exhaust manifold to suit a gt3540 and a 38mm wastegate but no turbo and gate. plenum cooler with pipes and exhaust manifold $2450 or very close offer!

850cc sard injectors(side feed) with rail and sard reg $850 or very close offer!

apexi power fc and z32 afm with harness $1000 or close offer!

or the complete engine with all the above for $8500, all you need is a 3540 and a gate and you got a reliable 10 sec package!!!!!

Als raceglides built c4 auto, full roller bearing, all the good gear inside, deep pan, transbrake, 3500rpm converter and a b&m pro ratchet shifter and tailshaft for r33. $4200 or close offer! box is awsome and still usable on the street!

offers only by pm or you can call Alex on 0413 311 919.

Edited by CRNAGE
Link to comment
https://www.sau.com.au/forums/topic/176318-fs-rb25-10sec-setup/
Share on other sites

Hey mate. Do you have any more specs of the auto. What power was it built to handle??

what specs are you after? it will cop 800hp no prob, this box will go in the 9's!!!

Where you located i want that power fc. Does it come with the hand controller and the wiring set up for a series1. P.M me asap........ P.S is his for a manuel

Edited by spudsr33
Where you located i want that power fc. Does it come with the hand controller and the wiring set up for a series1. P.M me asap........

sydney, no hand controller and yes its for series 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes to both! Yes to standard ECU and tune, but exhaust is aftermarket. Unsure on brand. Actually have it sitting in at my desk haha! I have to set it up on my laptop but this is a great next step, will do. So I generally try to shift before 4.5K RPM most times. I largely don't do a lot of high-rev driving, but I will take it up to red 1-2x a week max, as I know the occasional "Italian tune-up" is good for these cars.  Oh wow, is this way better than what I'm getting. Does this mean there's a good chance I have an issue?   Thanks for all the info so far guys.
    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
×
×
  • Create New...