Jump to content
SAU Community

Recommended Posts

  • Replies 63
  • Created
  • Last Reply

Top Posters In This Topic

You have the carpet in the boot?

Not the boot floor, but the trim on the side panels.

Only need it for the passenger side.

Also, might need the drivers side door trim.

  • 4 weeks later...
You have the carpet in the boot?

Not the boot floor, but the trim on the side panels.

Only need it for the passenger side.

Also, might need the drivers side door trim.

yes i do mate.. send me a PM..

you got the engine loom if so how much pm me!

sorry mate engine loom is being used in the conversion.

my brother was a bit busy to do the pms so ill do them personally soon.

thanks

mark.

so the headlights are buggered yeah?

yeah they are mate. sorry.. but LFS headlight lense is fine.. the mounts are cracked. but ur welcome to have that if u want to do some headlight conversion thingo.

ill get to the pm's asap

thanks

mark.

yeah they are mate. sorry.. but LFS headlight lense is fine.. the mounts are cracked. but ur welcome to have that if u want to do some headlight conversion thingo

Got any pics champ?

  • 2 weeks later...
coil overs still available ? spring rates / price and will you ship ?

after around 2000 for the ohlins come pick them up or i may deliver personally good condition RHR has lil dent.. does not affect it though :D

Yeah i remember you mate. Thanks champ.

Carl

do come out to archy again i got another dori car. perhaps we could do tandems in the near future :(

good luck finding ur parts. anything else let me knw bro

thanks

mark

hey buddy,

Is the LSD still available, will it slot straight into an NA 34

sure is mate. 300 for that if u want it.

Hey, is the rear right of the car damaged? Do you have the fuel neck? The part where the 'mouth' is when you refuel that goes into the fuel tank?

yep sure do whats ur offer.

Edited by markimak



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...