Jump to content
SAU Community

Greddy Emanage Tuner (se Qld)

50FFT

By 50FFT,
in Engines & Forced Induction

 Share

Recommended Posts

50FFT Community Regular

50FFT

Posted
Posted

Hey Everyone,

I recently have upgraded my turbo, injectors, fuel pump, afm and ecu.

I decided to go with a Greddy Emanage Piggy-Back computer cause it seemed the best for my street driven car.

Now the question is who to get to tune it, I don't know of many people that tune e-manage???

Any help would be good, and in S.E QLD too would help...

Cheers,

Matt

Link to comment
https://www.sau.com.au/forums/topic/177251-greddy-emanage-tuner-se-qld/
Share on other sites
UCD15R33 Experienced

UCD15R33

Posted
Posted

Good to see you when emange rather than a powerfc. As for tuning from running through diffferent forums I have hear that

GT AUTO GARAGE

5/150 Edmondstone Street

Newmarket 4051

and cafe 101 motor sport has done a few in there time.

Green_s13 Proficient

Green_s13

Posted
Posted

give pete from pro torque a call 0438 876 649

he tunned my emanage and helped me out heaps with getting it setup and running properly he is at slacks creek, he has tunned plenty of race cars and is very gentle with the car when tuning, he found and fixed up a few air leaks that i had and didn't charge for it. the tune itself isn't cheap but the emanage deos take a fair amount of timeto get them right. Also he knows the emanage back to front

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • GTSBoy
      R34 auto to manual conversion help

      By GTSBoy · Posted

      The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Manur33
      R34 auto to manual conversion help

      By Manur33 · Posted

      Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...