Jump to content
SAU Community

100,000k Service

shredder667

By shredder667,
in General Maintenance

 Share

Recommended Posts

shredder667 Rising Star

shredder667

Posted
Posted

so i died a little on the inside earlier this week as my speedo hit the precious 100,000k mark on the gtr :banana: . just wondering what exactly needs to be carried out for the service? timing belt has already been changed, but i'm assuming ALL fluids, plugs, filters and what else? cheers guys.

Link to comment
https://www.sau.com.au/forums/topic/177473-100000k-service/
Share on other sites
JonesyGTR Community Regular

JonesyGTR

Posted
Posted
so i died a little on the inside earlier this week as my speedo hit the precious 100,000k mark on the gtr :) . just wondering what exactly needs to be carried out for the service? timing belt has already been changed, but i'm assuming ALL fluids, plugs, filters and what else? cheers guys.

I will try and list all that i remember from when i did the 100k service on my 32 GTR:

Idler and Tensioner bearings

All belts (aircon, water pump, power steering)

Coolant flush and refill

engine oil and filter

water pump

fuel filter

radiator hoses, top & bottom

Diff oils

Transfer case fluid (atf)

Gearbox oil

Timing belt - even if it was 'done' when you bought the car, do it again!

Spark plugs

There are probably a few things i have forgotten, I will add them if i remember them.

BTW - i have all the above part numbers and where to get them from if you are interested.

Cheers!

Dan :D

Link to comment
https://www.sau.com.au/forums/topic/177473-100000k-service/#findComment-3241812
Share on other sites
LatinR33 Experienced

LatinR33

Posted
Posted

I just did mine bought a kit from Kudos motorsports and got it all done. For now ive done

Timing belt

water pump

idler and tensioner bearings

Seals

Cooling system flush and refill

Mechanic then just recommended changing radiator hoses and thermostat but all seems fine for now so will be doing it later :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/177473-100000k-service/#findComment-3243645
Share on other sites
Risking Grand Master

Risking

Posted
Posted

By all means replace the waterpump and idlers whilst the timing belt is off but when it comes to fan belts etc replace them as nessisary not becuase its a 100K service. If cam seals are not leaking dont touch them because chances are they will leak afterwards!! If itss aint broke dont fix it!!

Get all sorts of stupid things suggested daily but really treat it like a regular service with a timing belt. Replace worn items and keep driving.

Link to comment
https://www.sau.com.au/forums/topic/177473-100000k-service/#findComment-3245100
Share on other sites
LatinR33 Experienced

LatinR33

Posted
Posted

4 days from kudos?? I got mine in 2 days first thing in the morning at 7am from the courier. Top stuff there everything you need. top bloke. I changed seals because cant be stuffed paying money later on labour costs to change seals and after speaking to nissan they recommended changing seals also. So as they say aswell precaution is better than a cure.

Link to comment
https://www.sau.com.au/forums/topic/177473-100000k-service/#findComment-3246335
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      "Cheap" bolt on turbo on RB25DET NEO

      By Murray_Calavera · Posted

      The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • joshuaho96
      "Cheap" bolt on turbo on RB25DET NEO

      By joshuaho96 · Posted

      Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
    • GTSBoy
      "Cheap" bolt on turbo on RB25DET NEO

      By GTSBoy · Posted

      Intake manifold is not a part of the issue. The turbo bolts to the exhaust manifold. That is easy. But close your eyes and picture the physical situation. That is a T3 flange on the manifold and a T3 flange on the turbo. As long as any new turbo has a T3 flange on the exhaust housing, that exhaust housing will bolt to the exhaust manifold. This places the exhaust housing in the same place as the stock one. But now move your mental attention a little further forward. The location of the compressor housing is set by the length of the turbo's core. The stock turbo had a long core. Let's say that it is..... 100mm long. So that would place the compressor housing 100mm forward of the exhaust housing. But a highflow, might well have a centre core that is shorter. Let's say that it is only 70mm long. Now the compressor housing will be 30mm further back in the engine bay than the stock one. This DOES move the turbo's compressor outlet backwards. It also moves the compressor's inlet backwards. You will very likely have to do some work to both the inlet and outlet piping to make everything connect again. I am not say this to make it out to be a bigger deal than it is. I am just pointing out that "bolt on" is sometimes not quite bolt on. The highflow from GCG that Murray linked above (https://gcg.com.au/turbo-charger-upgrade-skyline-gtst-2iu-xtrgts-s1.html ) uses a core that is the same length as the stock core, and so does not require this extra work. It will look very much like the stock turbo. No-one uses GTR turbos of any flavour (stock, or aftermarket) in a single turbo application on RB20/25. It's not a thing. Yes, people have been putting on GT3076, GTX3076 (and bigger and smaller versions of those) and G30s (of various sizes) onto RB20/25 since forever. But these are not "bolt on". Everything except the 4 bolts to the exhaust manifold change with these. And genuine Garretts are expensive. Non-gen, like Pulsar, etc, are cheaper, variously as good or nearly as good. But still not bolt on. No-one in the right mind would pay for an HKS turbo. Not in this modern day and age. Well, yes, the GCG highflow. You could ask HG what he can do to make the compressor housing sit in the original location. There are surely others doing highflows around the world. And some of the eBay/Temu ones (as reported by Dose) work and don't die. Bit of a lottery though. I would send your turbo to GCG (here in Oz) to be highflowed if you want a trivial no-extra-work option. But seriously, the work required to change inlet and outlet piping is not that hard. That's a boost control problem, not a turbo problem.
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Thank you all for the replys 🙂 I know that intake would be different but that is one pipe at it is not that hard to get(custom one). I meant mainly bolt to the stock manifold and the turbo elbow. I looked and many sites/forums but they are just "old" with some old HKS turbos from GT-R i guess? What about some Garrets?  Or any other turbo? Is there even a turbo which i can just bolt on? 😄 And yeah i know about that new HKS but that is like 2000k USD without taxes/shipping in here   Iam getting a touch up tune but my "problem" is that on the "not" hot day iam getting peaks around 0,9 bar...and when it was around 15 Celsious i saw peak around 1 bar which is just too much for stock turbo. And of course turbo is old and i like to get some new one for a piece of mind 🙂 
    • GTSBoy
      new here

      By GTSBoy · Posted

      I'm working on the assumption that our friend Jasmine here is a Russian (or, possibly Ukrainian) spammer/spambot, based purely on the number of such that I have been having to neuter in the last few weeks. IP address for the OP above was in WA. But that could have been via VPN. Posting at quarter to 4 in the morning is a good sign of being from somewhere in Europe. The last Jasmine that I kicked in the cooch was IP addressed in Ukraine. Even that could have been via VPN, and the bitchbot could have been from Russia, Serbia, China or anywhere. Regardless, was a spambot, so I killed it with fire. The fact that our new friend Jasmine here did not respond in any way to my tart query strongly suggests to me that this OP was just the establishment phase of a user able to be activated for spamming in a week, or 3 or 10.
×
×
  • Create New...