Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I dont think the bov has siezed. It's possible don't get me wrong but i feel it was never set up right in the first place. When you have the factory plumb back there is only the one hose running from the bov to the plenum. Yours is tee'd into with another hose running to the nipple under the cross over pipe. This is not the original setup and where that hose is supposed to go. There should be no 't' piece in the bov line. I will take a pic from my car and show you what i mean.

Thw way you will no for sure if its the bov of the way its hooked up is when you put your turbosmart one on and if it flutters through out the whole rev range - not working, hence its the vac line steup. If it goes pschhh then its all good and the hks bov was stuffed.

oh ok, because my car has been setup this way since i bought it, aparently the previous owner of the car said he had to disable it because he was defected for it, but a picture of your setup will definatly help me out as im thinking maybe it was a waste of time me buying a new bov, thinking my apexi wasnt working... if i can get this setup working maybe i wont need to change my setup...

Ok here are the pics of the correct setup you should have.

bovdiagram.jpg

You have the hose (with the red arrow pointing to it) tee'd into the bov hose (yellow hose). Where as on mine but hoses are seperate and run to the plenum.

bovdiagram2.jpg

You can see here the same hose and the points it attaches to (marked with blue arrows)

Yours appears to be tee'd into the bov hose for some reason becuase the hormal point that this hose (red arrow) connects to on the plenum appears to be used by another hose running toward the passenger side of the engine by near the fire wall. Where is that hose running to? Does it go through the fire wall and into the cabin? Maybe the guy beofr you used it to get a boost reading for the gauge...

Hope this helps :D

Hmm thats wierd so the bov only has the one hose now running to the plenum? In that case the bov must have stopped working, probably stuck or something as said above. Maybe you should just put on your turbosmart one on in its place and hopefully that one will work. You will probably need to buy an adapter though to it can flange on like mine.

yeah it comes with adaptor, just got to wait for it to come in the post hopefully this week... will it hurt to have a cross piece (X) instead of a T piece so i can have my boost gauge branching of it? or will it reduce accuracy of my boost gauge having to many lines?

You can just tee your boost gauge into the a hose at the front of the plenum. It a little hose only about 8 cm long at the front the the plenum towards the drivers side, and it wont interfere with the bov etc.

  • 2 weeks later...

hey guys i ended up putting my new bov on and set it up the same way that the pictures show (R33silverS2) and still has the flutter sound.... ;)

anyone know whats going?

could it be i should block off what looks like a bleed valve on my turbo (brass fitting on turbo, with hose comming of it leading to nowhere)...

pics...

took it for a drive and it flutters but when given a little bit it does both???

if i give it a good rev it goes off the way it should...

would it need adjusting???

and how? (as i dont have a manual)

Hey mate thats what its supposed to do. ;) Mine does the same and so would anyone elses with aftermarket bov. The bov only opens under higher load conditions such as more boost or higher revs etc. The rest of the time it remains closed and flutters. You can adjust when it opens by turning the head of the bov to make it tighter or looser. The looser you go the less flutter you will get as the more the bov will open and make sound etc. Your setup sounds right just loosen the bov a little.

Although when i say load i dont mean load as in forth gear cruising at 60 with you foot to the floor for a sec, more like when the revs can increase quite freely (lower gears for example)- if that makes sense.

Edited by R33silverS2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...