Jump to content
SAU Community

Recommended Posts

Hey all.

i installed a drift bov today with plumb back or atmo i could choose either way but i choose atmo..

Since then its been running like crappolia..

Is there anything like a cpu upgrade or soemthing to fix the problem?Or is it just something i have to deal with

thanks

Link to comment
https://www.sau.com.au/forums/topic/178380-problems-after-installing-a-bov/
Share on other sites

Hey all.

i installed a drift bov today with plumb back or atmo i could choose either way but i choose atmo..

Since then its been running like crappolia..

Is there anything like a cpu upgrade or soemthing to fix the problem?Or is it just something i have to deal with

thanks

If its venting to atmo then you will run rich and your car will occasionally stall. Atmo BOVs on Skylines can be a bad mix. You can fix it up, DAFS.

happens to most people who install the atmosphere venting bov's. After a while you will learn how to adjust your driving so it doesn't stall. All i do is blip the throtle when coming to a stop ect. Do a search on the forum about this, been covered alot of times, you may find some use full tips.

Unfortunately blow off valves and skylines as some other member explained are not a good mix. I even use to have a GFB stealth that you get to adjust how much air is vented and how much is kept and car still didnt feel the same and idle was terrible. I know its not what you want to hear but if you want to have a car that runs well then install your stock bov.

i still have my stock plumback on my s1, no problems as in running, sometimes when letting clutch out a little to move forward in places like drive through with a little bit of throttle then go to put brakr on and clutch in cars idle does drop to close to a stall but then picks up again, only problem i have in regards to stalling hope this helps

Stalling when having a atmo bov installed is a really common thing. The reason it happens is because the afm detects the air going into the engine and puts more fuel in to burn the air, but the air is not getting into the combustion chamber, it's going out of the bov. I hope that made some sense.

As far as I know, it's something you just have to deal with if you're got a bov installed.

some people here adjust the idle just a little higher than stock, others just learn how to drive them like when you're about to stop change gear or clutch in when the idle is near idle speed. Or you rev it a little before you stop.

  • 2 weeks later...

The main issue with atmospheric BOV's is the AFM... Once air has gone past that it is accounted for by the computer, any difference an atmospheric BOV will cause means there is air accounted for, but not being used. With MAP sensor its a different story as it reads manifold pressures not airflow before the turbo. With the plumb back system the air goes back through the turbo or the afm keeping it all in the circuit of the airflow so the ecu can adjust according to the afm readings. Some cars just handle it better than others, my mates 32 used to be perfectly fine with big turbosmart BOV's but my mates 33 would stall all the time with a Blitz one and then the HKS one.

Liam

Edited by FordyR31

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No. The simplest wastegate hookup, with no solenoid or other form of "boost control" (ie, control over your boost control, if you know what I mean) is a single hose, direct from the turbo outlet/hot pipe, straight and only to the wastegate actuator. It is that pressure signal that drives the wastegate to open, providing the boost control (and by "boost control" here, I mean, limiting how high it can go, which is essentially the spring pressure of the actuator). You only end up with tee pieces and alternate flow paths once you start adding things to the boost control system to allow you to determine how much of that boost signal makes it to the actuator. There are so many ways to do that that there is no single way to run the hoses and tees and the like. If you have a stock boost solenoid, then all it does is either allow all the boost signal to go to the actuator, or open up to allow some of it to bleed off. There needs to be a restriction in that bleeder to allow only a small amount to bleed off. And in a stock system, that would then be plumbed back to the turbo inlet (for "emissions control" reasons). That is actually what that nipple on your BOV return pipe could/would be for. If you have an aftermarket boost controller and solenoid, then the above is mostly true, but there is no need for a restrictor in the bleed, because the solenoid is pulse width modulated to create a variable bleed off. The air that escapes from the bleed can either be vented, or also returned to the turbo inlet. For emissions reasons it should be returned to inlet, but the amount of air being vented is so small that it really doesn't matter (either from an emissions perspective, or from an air-fuel ratio affecting perspective).
    • And other times you just need to go buy bigger injectors?
    • Yup. I actually just blew my turbo. LOL.  should have checked this thread before today. i also have no boost solenoid. so it should be...one line from wastegate to turbo inlet, and a T somewhere in that line that connects to the wastegate return pipe?
    • It's recommended, however I can assure you a good amount of people don't bother. FWIW, the OEM battery lasted 4.5 years and I changed it prematurely too, I reckon could have stretched it to 5 years.
    • Are you telling me I'm going to need a code reader etc to just change the battery when it dies...  Why did I let you talk me into allowing Kate to buy this car lol  
×
×
  • Create New...