Jump to content
SAU Community

irridium spark plugs

croat

By croat,
in General Automotive Discussion

 Share

Recommended Posts

croat Mentor

croat

Posted
Posted

When driving along on an open road in 2nd gear or above and i go full throttle, when the revs hit around the 5000+ mark the engine does not run as smoothly as before and begins to like missfire and the exhaust begins to backfire as if there is too much load or stress on the engine. Anyone know what this is? Some one said new irridium spark plugs would fix it? what are ur thoughts?

Thanks...

Link to comment
https://www.sau.com.au/forums/topic/17890-irridium-spark-plugs/
Share on other sites
darkstar Contributor

darkstar

Posted
Posted

The fancy iridium and platinum plugs are great for cars that are factory, and no forced induction. Greater service intervals and so forth.

For performance cars, standard plugs with the right gapping, and perhaps running a slightly colder plug does the trick.

A freind had a misfire just as he got on boost on his soarer, running 1 bar. While in the car you couldnt feel it or notice it, but on the dyno you could clearly see that was struggling at a particular point on the graph, and it was doing it almost all the time.

Gapped down to 0.8 and ran a colder plug, using standard NGKs, problem solved and t he car runs better. He has platinum plugs in there before, which were fairly new.

The iridium plug has a very small tip on the end of it, and its very fragile, expecially when exposed to the elements of high boost. Even a light detonation pulse with the front focused on the centre or starting out from the centre, could melt the tip or deform it in a way that the spark integrity is sacrificed.

9-10 second vl turbos run approiately speced standard NGKs with no problems.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Duncan
      NC MX5

      By Duncan · Posted

      Quite right, if you make it to that pension you deserve every cent
    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...